Jump to content
SAU Community

S13, 180sx, Parts, Engine, Gearbox, Nismo, Bottom Ends, Heads, Manifolds, Exhaust, Turbo, Gtr Rims, 5 Stud, Front Mount, Apexi


Recommended Posts

PICS UP SOON

SR20 BOTTOM ENDS MUST GO Taking up space!

All going cheap need quick sale!

SR20DET Engine $1500

Fresh imported engine from just jap with receipt 2 months old

Gearbox with slave cylinder and line and shifter $600

Apexi turbo timer with wiring harness $100

Apexi AVCR boost controller all wiring $600

Front mount intercooler kit with piping and blow off valve $200

3" Straight through exhaust turbo back $200

Mandrel bent, high flow cat and heat wrap

s13 rear brake calipers $100

s13 skyline front brake calipers made to fit s13 $150

Nismo braided clutch line $100

Tail shaft $100

Five stud conversion kit $500

ICHIBARN from USA bolt on with genuine new wheel bearings

Nismo braided brake lines $200

R32 GTR wheels $500

With tires

REAR DIFF CV SHAFTS $50

2x sr20 red top standard turbos $100 each

2x sr20 red top heads "top end" with cams and bits $300 each

2x sr20 bottom ends $300

One seized from fuel in oil

One turns detonated piston 2

MUST GO

2x sr20 exhaust manifolds $80

2x sr20 intake manifolds $80

ECU red top standard $100

ECU red top nistune! $300

Can retune!

Tuned for 300HP fmic, disco spud and greddy easy cams

Will need retune depending on your application

PICK UP ONLY

PREFER TXT OR PM 0423428670

s13 skyline front brake calipers made to fit s13 $150

Calipers only? No rotors? How are they made to fit an S13?

As listed calipers only

Re drilled and tapped to bolt straight on!

s13 skyline front brake calipers made to fit s13 $150

Calipers only? No rotors? How are they made to fit an S13?

FFS! Yeah thats nice

BUT im trying to sell stuff not fkn, have a debate about whats what!

So PLEASE keep comments to self

  • 1 month later...

Hey mate,

SR20DET Engine $1500

Fresh imported engine from just jap with receipt 2 months old

Is the engine still available? Any idea on the kms on it please?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...