Jump to content
SAU Community

Recommended Posts

Hey guys up for sale is my r34 that has had no expense spared. It had a motor change (rb26) about 25k kms ago and is holding up perfectly, the car is making 291rwkw atm on safe tune (mines ecu) and will be putting out close to 350 with the new computer (power fc jetro). This car has been fully built by race pace and has been built to last.

MOTOR RB26

New forged pistons (race pace)

new forged rods (eagle)

new r33 gtr crank

new head

new high pressure/volume oil pump

new water pump

new race pace modified adjustable cam gears

new garret twin GT-SS turbos with upgraded actuators

new tomei gtr fuel pump

new modified sump

gtr intercooler

gtr injectors

apexi pod filters

new extreme cushion button clutch

3" high flow cat

3" exhaust system, car is very quiet

New front and rear r33gtr brembo brakes and new 324mm disks (front are slotted) (rear are drilled)

REAR END

Hks coil over hyper D, adjustable dampen

New lsd

Adjustable toe arms

Adjustable traction rods

Adjustable rear camber arms

Machined sub frame bushes c type

INTERIOR

Retrimed "too black" with red stitching

Drift gear knob

Blitz boost gauge

Sony dvd player "touch screen"

Turbo timer

Fire extinguisher

th_l_2f1774799c91a227e418741b19249b-1.jpg th_l_85d0adb7cf6cf25fb914d6f5f3fce8e6.jpg th_l_9b747088365852dbf805a7c34ab70793.jpg

if needed i can supply many more photos by either mms or email, i have most receipts and dyno sheets if needed. car has just been serviced and is in overall A++++++ condition

please no ridiculous offers and keep the stupid comments to yourself

car is located in murrumbeena, the custom plates may be included in the sale depending on the negotiated price

0433049322

Link to comment
https://www.sau.com.au/forums/topic/286029-vic-r34-rb26dett-eoi/
Share on other sites

EOI pepe... make an offer, if its worth my while to sell the car i will other wise ill keep it as Ive spent way too much $$$ on it

th_05072009254.jpg th_20072009003.jpg th_29082009066.jpg th_29082009068.jpg

Edited by s14_boosted
  • 3 weeks later...
  • 3 weeks later...
  • 5 weeks later...

i went and had a look at it today... i had to go home and change my undies, ill be picking it up nxt week sometime as theres a few parts to still put back on nd stuff,

offers over $30k

30k aint much as its a fully built r34 wit a top notch showroom paint job.

  • 1 month later...

forgot to add

*new s/steel upgraded front pipes

*new race pace made high flow muffler

*new high flow radiator + hoses

*aircons just been re gassed (icy cold) :ermm:

*the side skirts broke when the car was getting painted so the 1s on there now are brand new (bomex)

*new rear windscreen they cost big $$$ with fresh tint as old 1 had slight wiper wear

*fresh tread on all 4 rims + rw tread on other set of rims included in the sale

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers)
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
×
×
  • Create New...