Jump to content
SAU Community

(psi033) R33 Gts-t 250rwkw

arthurde
 Share

Recommended Posts

arthurde Apprentice

arthurde

Posted
Posted (edited)

Car is in immaculate condition, serviced every 5,000Kms, Brand new timing belt,water pump and all auxiliary belts.

Has new in car entertainment system fitted by PPA Car Audio worth over $2,000. Has Brand new Yokohama Street slicks done less then 500km's (255/40/R17).

Nothing Needed to spend for RWC.

Car has been dyno'd and makes 250rwkw at 15psi

Modifications as listed below:

OS Giken Twin plate clutch, C's Short Shift Kit, A-Tech lightweight rims, Stainless Steel Braided Brake Lines,Apexi Coil overs, Cusco F&R strut braces, Nismo Sway bars, Whiteline Sub frame Bushes, Apexi Power Pod Filter, Apexi Solid steel intake pipe, Apexi Power FC w/ hand controller, Apexi Power FC Boost Control Kit, ATP Stage 3 Hi Flow Turbocharger, Z32 AFM, Nismo Fuel Pump, Nismo 555cc Injectors, Full 3" Exhaust with split dump pipe, Greddy FMIC kit, Greddy Oil Cooler Kit, Greddy Oil Filter relocation kit, Greddy Oil temp, Oil Pressure and Boost Gauges, KOYO Alloy Radiator w/ header tank, Nismo 1.5way LSD

$18,500 ONO

0431074537

019.jpg

002.jpg

013.jpg

Edited by arthurde
Link to comment
https://www.sau.com.au/forums/topic/290347-psi033-r33-gts-t-250rwkw/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • nash47
      Cas issue

      By nash47 · Posted

      Yes sir am asking is there possible way from aem tuner from wiring pins 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...