Jump to content
SAU Community

New Turbosmart Hpergate 45mm In Combination With Greddy Profec B Spec Ii

engo

By engo,
in Engines & Forced Induction

 Share

Recommended Posts

engo Rising Star

engo

Posted
Posted

so i ran the car down today to have my new dump pipe and screamer made up... i have a high mont t04e with a hypergate 45mm external gate...ebc ( greddy profec b ) i had a jjr external gate on it before and since the change i cant get it to boost over 5 psi..the gate just opens no matter what ... i tried playin with the boost controller up the boost n that...still 5-6 psi ( which i assume is the ext gates spring ) now the ebc was installed all perfectly cause i have been running 16 psi with the other ext gate .... only changes i have made is now i have 2 vcuum lines goin to the gate ( the old one i only had one,comin from the solenoid) but now i have one from the plenum aswell... and that vacuum source used to go on my microtech ecu but now has changed to a power fc... i am completely stumped to y the boost controller is basically in active .. it still reads the boost and everything on the profec b... any ideas??..could it be the vacuum lines??

any help would be greattt :(:D

alex

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Duncan
      R32 GT-R: 4WD Light Turns On After Bumps – Code 19 (ETS Motor) But No Issues Found

      By Duncan · Posted

      Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...