Jump to content
SAU Community

Recommended Posts

My car has been running very hot for a while in between half and 3/4, i just recently got my radiator flushed and was told it was 85% blocked :flamed:

They also informed me at the time i needed a welsh plug replaced.

ANYWAY The car still seems to be running hot its not dropping any water now though.

Also how easy is to do a head gasket on a r32 could this be possible? i have checked and so far found no evidence.

Link to comment
https://www.sau.com.au/forums/topic/29104-im-worried/
Share on other sites

i'd buy a second hand or reco'd radiator and get the welsh plug fixed...

you can warp the gasket.... but i dont think your car is getting hot enough to do that.... but act on it asap cause the longer you leave it the more damage that can happen later... and the more you "get used to it"

Happened to my dad.... he found out the hard way ....Boom!!!!

$$$$$$ later reco'd engine. Goes better now!! (it was a Jackaroo)

Link to comment
https://www.sau.com.au/forums/topic/29104-im-worried/#findComment-598057
Share on other sites

yeah Pekatu thats normal

It should always stay at 1/2 no matter what. Any more and your in trouble!! I learnt this the hard way, i blew the head gasket on my last car and it cost me $$$

The stock gauge is fairly accurate, but an aftermarket one it will go up or down +/- a few degree's depending if you thrash it or just cruising...

Always keep coolent/water in your boot and if you ever see the guage go over 1/2 pull over before it gets too hot and see where a leak may be. Then top up your radiator and cruise your car to home/mechanics

Link to comment
https://www.sau.com.au/forums/topic/29104-im-worried/#findComment-598620
Share on other sites

You might want to take a look at ur thermostat. In other words buy a new one cause there not expensive. They have a tendancy to jam half open wich will cause your car to run hot. If it was the head gasket you would be using heaps more fuel that u usually do and there would be a lot of black smoke out the exhaust from richness. Worth a thought.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/29104-im-worried/#findComment-599018
Share on other sites

How does a blown head gasket cause the car to use more fuel?

It will often allow water to get into the combustion chambers, giving white smoke out the exhaust, or may let oil in, with a bluer smoke out the exhaust.

Try the thermostat. If that doesnt work, do the waterpump, and make sure you bleed the system of air, there are bleed bolts (10mm head on my R31) on the intake plenum/manifold.

Good luck.

Link to comment
https://www.sau.com.au/forums/topic/29104-im-worried/#findComment-600072
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...