Jump to content
SAU Community

Recommended Posts

OK I got some general maintenance done such as rocker cover gasket, timing belt, water pump etc, also radiator cleaned out.

Also added new 3" turbo back 'zaust, plus a POD filter.

That is it no other mods. It's a R33 GTST.

Now I drive it home with the widows down and thought it seemed hot but thought it was my imagination, also thought I smelled a bit of burning but dismissed it. I drove it tonight with the windows down and you can feel the heat from the foot well and fwd part of the central tunnel. Doesn't seem right. I wasn't boosting about and was driving fairly normal. Drove straight home and was worried about fire or something. I mean it feels REALLY hot.

Water temp gauge looks ok, but I notice quite a bit of activity from the oil pressure gauge; it's up and down quite a bit with the throttle. Always before it would seem to do very little, just show pressure in about the middle until the car was warmed up.

I'm thinking my engine should be a bit hotter 'cos I've probably gained 20 kw or so from the 'zaust but the heat has me worried. Can't call the shop 'till Monday so won't drive it until I check it with them.

Edited by Tony de Wonderful

Did they put the stock turbo heat shield back on?

When I got my brand new turbo back exhaust system, I felt something similar as well. Could feel excess heat when I'm stationary with windows down & I had a burnt smell as well.

If the pipes are new, the burnt smell is mostly normal. But when I 1st drove the car back that burnt smell scared the sh*t out of me as I thought my engine caught on fire & I pulled over like several times just to check the engine bay on my way home from the workshop.

After a while though, the smell gradually disappeared & I don't seem to be able to notice the heat anymore.

Edited by Mayuri Krab
Did they put the stock turbo heat shield back on?

When I got my brand new turbo back exhaust system, I felt something similar as well. Could feel excess heat when I'm stationary with windows down & I had a burnt smell.

After a while though, I don't seem to feel anything anymore though...

Good point. I'll ask them on Monday.

The oil pressure gauge has me worried though. I don't remember it bouncing around before.

You can check if the shield is on or not, just pop the bonnet & look for the turbo, if you can see it then the heat shield is not on. I would ask them for the old shield back & put it on, as it seem to block quite a bit of heat from the turbo coming upwards.

Also what are you seeing from your oil pressure? From what your description it seems to me like your gauge wasn't working correctly b4 & now it is...

As my oil pressure will move frequently with throttle once the engine has warmed up. Mine usually moves in the range of 2 to 6 (idle at 2 & goes up to 6 under heavy throttle).

only way to know for sure what is happening temp wise is to either get a proper temp gauge or borrow/buy a consult cable and hook it up to some software to read the exact temp. no point just guessing that it is hot if it turns out that the temp is actually fine.

edit: also you can pretty much ignore the stock water temp gauge. it will stay in the normal position up until a bit over 100 degrees when it will suddenly jump to hot.

i reckon the burning smell is normal.. new metal and exhaust putty and new gaskets etc.

and witht the guage maybe you didnt notice it before cos you wernt worried by the burning smell??

check the heat shield on the cat as well as the turbo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...