Jump to content
SAU Community

Recommended Posts

lookin for a r32 rb20 hicas ps pump. no powersteerin for over a week now, handles like a tank. willin to pay around 100. on sunny coast qld. pm on here or sms 0403107932.

Link to comment
https://www.sau.com.au/forums/topic/297180-wtb-rb20-ps-pump-with-hicas/
Share on other sites

Hi man

I can help with the hicas pump out of my r32 gtr for 100.00 plus postage i rec on about 30.00 registered.

i know it is good as it is still conected and my car was pulled off the road about 8 weeks ago.

stuart 0409135950

is it the same on the rb26 mate? not sure. hoping for a bolt out bolt in job. hopefully is direct replacement. i think theres only the one pump running from crank that runs the lot. or is ps pump separate from hicas pump?

Edited by Jason32gtst

Hi man

does your pump have any numbers on it as i have a r33gtst pump and another it may be off r32 gtst that i had to do a conversion on for a mate 6 months ago.

It has one inlet pipe comming from resivour and has kyb on back housing and i thing it says 189 on to of housing and it is black in colour

stuart

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...