Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...
Where did you found them ? where are they based in Australia ?

FOUND THEM DOING A RANDOM SERACH ON GOOGLE

I EMAILED THEM AND I FIND TO FIND OUT MORE

YOU HAVE TO PAY 20% DEPOSIT FOR A CAR YOU WANT TO BUY, THEY ADVERTISE THE CARS ON THEIR WEBSITE

BUT THE WEIRD THING IS THAT THE CARS THEY ADVERTISE ON THEIR SITE THEY DONT HAVE, ITS ALL THROUGH AUCTION??

AND IF YOU CHANGE YOUR MIND AND DONT THEM TO LOOK YOU DONT GET YOUR DEPOSIT BACK

HMMMMMM

They look legit to me. Looks like a private import who has just started a site up but not having an ABN and only a mobile phone number wont given anyone much confidence in them. Its a bit strange that they dont have an ABN, they definitely need one by law.

http://www.facebook.com/group.php?gid=4934...4707&ref=mf

Edited by BigWillieStyles
They do have an ABN:

ABN: 46 372 838 328

Entity name:

BUTROS, MENA

Trading name:

Osaka Performance Imports

All that is a personal ABN you get if you want a second job, until they comply with the fair trading laws and Motor Dealers Regulation 2004 in NSW they are not able to Broker cars as per stated else were or below.

Motor vehicle consultant licence

Allows you to advise others about where they can purchase a particular vehicle. A motor vehicle consultant cannot be a party to the sale of any particular vehicle.

And as you can see below Brokering a car from Japan isn't excluded in NSW.

Exempted vehicles

You are not required to hold a licence under the Motor Dealers Act 1974 if your business is conducted only in relation to buying, selling or exchanging the following:

* cranes, hoists or conveyors, as defined by the Occupational Health and Safety Act 2000

* motor vehicles or second-hand motor cycles (not including new motor cycles) that are incapable of being registered in NSW

* motor vehicles which comprise an excavator, road grader, road roller, bulldozer, fork lift truck or other equipment other than a tractor and which is not constructed on a chassis of a type normally used in the construction of a motor lorry

* motor vehicles constructed or adapted for road construction or maintenance, including cleansing, sweeping or watering roads

* trailers that have a tare weight of 250 kg or less.

  • 2 weeks later...

I vouch for the owner of the company and although the company is new it stands by their customers im sure Mena would be more than happy to answer any questions in regards to any of his stock as his helped me in the past with items ive purchased in the past. Please leave speculations aside until you have dealt with the shop there is no point putting opinions forward unless you have had experience for better or worse

Edited by Hiroshima Screamer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...