Jump to content
SAU Community

Recommended Posts

Agreed - very cool - have been meaning to try it sometime but haven't yet.

There are two ways to do it - the proper way (as gadl above does)

and the cheating way where you take one pic and do it in PS in 3 steps

(obviously not as good!)

Here for example is one I made the cheating way (pretty crap)

before

2009_02_05%20Brisbane%20CBD.jpg

after

2009_02_05%20Brisbane%20CBD%20Land.jpg

Link to comment
https://www.sau.com.au/forums/topic/297679-wee-planets/#findComment-4954920
Share on other sites

1. Convert the photo into a square image

Use the Photo|Image Size menu item to change the image size into a large square. Uncheck ‘Constrain Proporties’ and set the “height” value to the same value as your “width” value.

2. Turn image upside down

Rotate by 180°

3. Apply the polar effect

“Filter|Distort|Polar Coordinates” filter - choose the “Rectangular to Polar” setting

When selecting a photo to start with you should keep the following things in mind:

  • Select a panorama photo or a cropped landscape photo (aspect ratio at least 2:1, which means the width should be at least two times the height).
  • The bottom area (bottom 25% or so) of the photo in most cases should have only very little detail (e.g. sand, asphalt, water). This area will later be in the middle of the picture and will also be distorted the most.
  • The upper area (upper 25%) should also have only little detail, most preferably just one color (e.g. blue sky, night sky etc.).
  • The left and the right border of the photo should neatly fit into each other (which is always the case for a stitched 360° panorama).
  • The horizon must be exactly horizontal, the left and right end of the photo will be joined together and if they are on different heights your planet will have a big crack in the surface (again this is no issue for 360° panoramas).
Link to comment
https://www.sau.com.au/forums/topic/297679-wee-planets/#findComment-4955114
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • What Duncan said sounds right. Also, it looks like they only have the driver's mat. Not the rest. Because looking at the diagram: KG4911 is just the mat for the driver. KG4900 is the full set if I'm not mistaken and discontinued.   But, it looks like they may still have the full set for the manual S2. Might be worth checking for the other models as well as they seem slightly different. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/misc/G49 Man, I'm tempted.
    • I dunno about that as a blanket statement. Pitwork is Nissan's "Nissan genuine" thing, and for stuff like timing belts, I have found them to be excellent. Of course, for things like oil filters, you always use proper trusted brands anyway, not whatever the OEM has taken to using.
    • Ahhhh... If you were putting 12V to the led in there, that's likely made it very unhappy. Chances are how you put power, was 12V across an LED that's meant to only have about 20mA through it at peak, and a forward voltage of about 1.8 to 2.4 volts. That circuit is likely only a 3V3 circuit, and will have a resistor in series with the led too. That's my guesstimate on that light, without having touched one.
    • Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
    • I have had too many of those over the years, my cars have a toolkit or at minimum a cheapy multi tool thing because its too easy to be snookered by some stupid plastic clip that stops you checking the battery terminal isn't loose.
×
×
  • Create New...