Jump to content
SAU Community

Recommended Posts

Have the following for sale, still on the car can see running etc, made over 300kw on 18psi with current tune, most parts are brand new and have just been fitted within the last 2 months, can buy the whole lot or will separate.

located in Adelaide

- Garrett GT35 Turbo with 0.5 front cover (faster spool then 0.7) and 0.82 rear IW & Custom Braided lines oil restrictor and custom turbo drain etc $1850

- Tune Length stainless exhaust manifold $300

- 3.5 "Bell mouth dump front pipe $350 suit gt35 IW

- 3" Silicon Hard intake pipe & Pod Filter $100

- Trust Side mount intercooler (uses short piping and goes back into stock piping) $400

- Z32 AFM with plug $250

- SARD 850cc side feed injectors with clips and loom all soldered in $850

- Yellow Jackets coil packs $300 suit r33 series 2

- Apexi Power fc + Apexi Commander with 300kw tune $1450 suit r33

- BLITZ Sbc ID3 SPEC-S Electronic Boost Controller $400

- Nismo 400r Sideskirts suit r33 $300

- Cusco Coil Overs $800

- 18" x 9.5 Dtm rush wheels stretched 235's new tyres front, 255's 1/2 tread rear $1500

- Rda slotted rotors & QFM-k750 hight temp pads $450

- Nismo Fpr $120

Edited by FOOLBOOST
  • 2 weeks later...

still got injectors,, would they fir rb20det?

yes, they are side feed so no they wont, come with collars o-rings, fuel rail, loom etc bolt in

Hey mate got 200 for the coilpacks if u will take that if so pm me cheers

Tell him hes dreamin

Are the brakes front, back or both??

Brakes are complete set of front and back discs and pads used for 2months

Hey mate, i need new coils, how do these compare to Splitfires? Obviously a fair bit cheaper so i assume they are not as good? Or is that a mistake...

Edited by nelly
Hey mate, i need new coils, how do these compare to Splitfires? Obviously a fair bit cheaper so i assume they are not as good? Or is that a mistake...

Same as Spitfires ask Performance Wise who sells them

Edited by FOOLBOOST

Xmas specials

- Garrett GT35 Turbo with 0.5 front cover (faster spool then 0.7) and 0.82 rear IW & Custom Braided lines oil restrictor and custom turbo drain etc

Also comes with new 19psi actuator, and hks alloy hard out let elbow to suit. $1700

- Trust Side mount intercooler (uses short piping and goes back into stock piping) $350

- Z32 AFM with plug $200

- SARD 850cc side feed injectors in rail with clips and loom all soldered in $750

- Yellow Jackets coil packs $280 suit r33 series 2

- Apexi Power fc + Apexi Commander with 300kw tune $1300 suit r33

- BLITZ Sbc ID3 SPEC-S Electronic Boost Controller $350

- Nismo 400r Sideskirts suit r33 $200

- Rda slotted rotors & QFM-k750 hight temp pads $400

Edited by FOOLBOOST

will the gt35 turbo bolt upto the standard manifold?

It might actually as has the smaller comp cover, havent tried it as using that low mount manifold if it didnt could always use a 10-12mm spacer. Will put more pics up today.

hey mate pic's of side skirts please?

post-31991-1261964562_thumb.jpg post-31991-1261964572_thumb.jpg post-31991-1261964582_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Not sure what you mean by electronic speedo drive.  Speedo reads fine up to 180 yes.
    • For anyone interested, this is my old graph from 2021, but I've plotted the previous setup curve onto it with a black pen. old setup was: pon cams, oem itbs and plenum, HPI manifold, hks 2835 pro S .87ar rear, Turbosmart actuator, 3" turbo back no res. or cat., greddy spec M fmic, nismo 740cc inj, walbro in tank 460, splitfires, 4" intake pipe, Apexi pod, e85, eboost2, power Fc. I love that the new setup has much larger turbo spec with the HTA3076 1.01ar Ts rear, and literally everything is bigger, but far higher quality and result is it's FAR more responsive in paper.
    • This makes a lot of sense! I just had that realisation a few minutes ago and wrote it above haha. This is a good new discovery. "Sanding the side of the hill" perfect way to put it.   😂 😂 
    • This is probably what's happened to me. I'll put filler again on my repairs and use the long block and let you know how I go. Fingers crossed it's my last batch of filler lol. I can see that happening where my block dipped at certain points because it didn't cover all the high spots at the same time if that makes sense. I'm just trying to visualise the fact that with the large sanding block I will be sanding far away from the central dent area and whether that will cause issues or whether that's going to fether out my repairs better.
×
×
  • Create New...