Jump to content
SAU Community

Recommended Posts

Vechile: 1988 mazda s4 rx7

Reason for Sale: Loss of License

Price: 10,500

Contact: Julian, 0439315960

Location: Sth/Est Melbourne

Vechile Details:

Trying to be as honest as possible about any faults with the vechile

COMES WITH RWC and 6 months Vic Rego.

1988 MAZDA FC3S RX7

Gun Metal Gray- Series 4 Japanese Import

Very Low 92,000km

Body:

Clean overall with no rust AT ALL!

Few small dents and scratchs, nothing serious.

Front bar paint is average in afew places and when previous owner removed rear wing has a small dent.

JDM series 5 tail lights.

Engine:

Standard 13B Motor,

Microtech Lt-10’s Computer,

HIghflow Turbo with Enlarged wastegate for more flow.

Hidden pod filter under airbox.

2.5” turbo back exhaust, rotaflow mufflers, quiet.

Malpassi Rising rate Fuel reg

Bosch 450hp internal fuel pump

Upgraded injectors

Exedy Heavy Duty clutch and Machined flywheel 2,500km ago

160rwkw at 8psi, with dyno sheet.

Suspension:

Tein Superstreet coilovers, fully adjustable, front and rear.

Have been correctly setup on suspension dyno.

Front and rear whiteline adjustable swaybars.

Front and rear high performance brake pads.

Interior:

Very clean original black interior.

Pioneer Head unit with Speakers.

Sparco 350mm Steering wheel.

Autometer boost gauge.

Wheels:

F-

17x8-Koya Driteks- 235/40r17- Yokohama S-drive Tyres

R-

17x9-Koya Drifteks- 255/40r17- Yokohama S-drive Tyres

Extras:

Freshly Reco’d Aircon, icey cold.

6 Months Victorian Registartion.

Central Locking with 3 point immobilizer

Pics:

IMG_0050.jpg

IMG_0048.jpg

IMG_0044.jpg

IMG_0038.jpg

IMG_0036.jpg

IMG_0035.jpg

Link to comment
https://www.sau.com.au/forums/topic/312462-rx7-fc3s-jap/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...