Jump to content
SAU Community

Recommended Posts

Hi all,

Just imported a r34 gtt , its stock standard...done around 90,000.... just recently if i've got my foot planted it missfires pretty bad through 4.5-5.5k revs, and stops after that.... it doesnt do it if i accelerate more gently through those revs

Anyone have anyidea whats causing this?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/324651-missfire-45k-55k-revs/
Share on other sites

Splitfires are a bit of a rip off now, around $600+ new from memory. Might be better off trying to source some barely used second hand ones from this forum, or alternatively go with a different brand.

Edited by Dani Boi

i had a very similar problem once, and despite everyone telling me it would be coilpacks, it turned out to be a bad connection to the CAS..

my suggestion is not to go out buying a bunch of gear you may not need.. take it to one of the garages from the consolidated workshop thread and they should be able to tell you the cause pretty quickly and it will save you money in the long run.

before you buy new coilpacks if u wanna save some money (this isnt a permanent fix) change your spark plugs and gap them to about 0.75mm - dont go less then 0.7 and dont go more then 0.8. sometimes this will stop the missing

600$ !! thats lame. let alone if i get somewhere like x-speed to do it, probably cost me around a grand =/

:P WOW! You got a Skyline and don't even want to pay $600 to repair it? Skylines are money pits, get used to it. Wait til your clutch goes...and even better wait til the turbo dies on its hole.

Bit of advice, if you don't want to pay workshop markup on parts, source out the parts yourself and just pay the workshop for the labour. Will save you quite a bit in the long run.

I'd be pulling out my plugs and checking the condition/replacing them. is the engine running higher than standard boost? if not re-gapping shouldnt be required. if that fails being the next cheapest option i'd do a upper cylinder purge (u.c.p.) personally i use a product called "injector max" to ensure the injectors are clear and fueling properly and the back of the valves/piston heads are clean, just did one today on my R33 and can really feel the diffrence it made! If that doesnt fix it i'd be focused on the coilpacks. (might be a good idea to buy just one known working second hand standard coil then swap it with the rest one at a time to see if this eliminated the problem as it could just be one dodgey coil pack behind the whole miss) it takes a little bit of time but its better than $600 for a set of splitfires ya know :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...