Jump to content
SAU Community

Recommended Posts

Like last Friday/Thursday? Mass amounts of police pulling people over for speeding on Mitchell Freeway after City West before Leederville Traino.

Remember its 80ks until you pass Vincet Street exit. Saw alot of vans and tradies getting tickets.

Seems like they may be doing this on a regular basis so watch out!

Link to comment
https://www.sau.com.au/forums/topic/326264-bikercops-on-the-freeway/
Share on other sites

I got done for 95 in an 80 zone by the exact same thing.. except on the OTHER side of the city. Just after the swan river bridge, they were hiding around a corner just before it turns 100. Damn those sneaky popo :l

At the part of the freeway more people are already traveling closer to 100 than 80, I can't see the reason why it can't just be 100, but that's the reason the cops are there. Revenue, not safety.

yeah, I've seen them there a couple times... usually on a friday morning. about 5 bikes in a row, with one guy with a radar gun. He'll give a wave and point and they will be off, on after the other. I watched them for a bit, while waiting on the thomas st off ramp. It sounds like they have found a great way to make money, other then multinovas :miner:

Better watch my a** then. But so far I found almost everyone would be driving at least 10km/h over at the 80km/h freeway zones so I usually just follow the pack... eehh safety in numbers?

Speaking of which I just went past one of those dual function cameras at Leech/Albany highway, those things looked way different from the regular single red light cameras also i have added an additional warning POI in my GPS :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...