Jump to content
SAU Community

R33 Gtst 95 Model Skyline

32-Mspec
 Share

Recommended Posts

32-Mspec Collaborator

32-Mspec

Posted
Posted

Located on the Gold Coast

Needs to sell, as im going over seas and need spending money.

12000 ono

Up for sale is my 1995 model r33 Gtst Skyline

5 speed manual

Will come with few months Rego, and Rwc if bought before it expires

has splitfire coilpacks

boost guage pillar mounted

great interior

crack free dash

SRS airbag on steering wheel for extra safety :D

front mount intercooler

custom 3 inch exhaust with 2 pipes coming off the end :cool: , gives it a nice tone

turbosmart BOV gives nice flutter sound

Full Kenwood sound system, except sub and amp, however have got plugs running from back of head deck to the boot, so all you need is sub amp and sub wiring kit :)

17inch work wheels.

400r bar, side skirt and rear pods

JUST CASH OFFERS NO SWAPS

post-63714-1277722745_thumb.jpg

post-63714-1277722770_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/326698-r33-gtst-95-model-skyline/
Share on other sites
32-Mspec Collaborator

32-Mspec

Posted
  • Author
Posted

has had the timing belt, tensioners, all seals and gaskets and water pump replaced, so that saves who ever buys this doing that, and the stress of whether its gonna go, but since its been done means it wont go :D

32-Mspec Collaborator

32-Mspec

Posted
  • Author
Posted
how many kms does the car have?!

has about 177XXX might seem high but has had the timing belt, and all that replaced as i said up above, and i can guarantee that as im the one who paid for it, its not like how other cars are for sale and the seller says "oh the guy i bought it from said he replaced it"

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...