Jump to content
SAU Community

R30 Extractors And Hotplate Q

r3volt21
 Share

Recommended Posts

r3volt21 Apprentice

r3volt21

Posted
Posted

Hi,

I own a mr30 sedan and have my eye on some patrol 2.8 petrol extractors from a local wrecker and was just wondering if some1 could please tell me the amount I need to bring the flange back to make them fit.

I also scored a pair of s1 red on red hotplates for it for free from a friend who wrote his off they have a chunk missing right at the top of the left one and i wouldnt worry as its hardly noticable when on the car but they get water behind, I was just wondering if anyone knows what i could repair this with doesnt have to look that great as i want them in more to make sure i like that style before tracking a good cond set down.

Thanks in advance,

Paul.

Link to comment
https://www.sau.com.au/forums/topic/327439-r30-extractors-and-hotplate-q/
Share on other sites
Factory 5 Mentor

Factory 5

Posted
Posted

flange wont need modification. the last bend before the pipes go rear-ward will maybe need bending. (just depends, not every set out there is the same. there are a few manufacturers)

clear lexan/perspex or whetever the lights are made of is very hard to repair properly. most adhesives and epoxy will make the inside go all foggy and shit. your best bet is to just use the Aus lights, hotplates arent that special (car wont go any faster)

r3volt21 Apprentice

r3volt21

Posted
  • Author
Posted

thanks for the replay mag86 are thats even easier to just get it bent to fit looked at mine properly i dont have the flange their anymore anyway my engine pipe has just been expanded at the end and welded straight to my 2.5' exhaust, I might just have a play with the lights, i have some plastics that might work.

Ghostrider Grand Master

Ghostrider

Posted
Posted

If your trying to repair the lights, like just cracks, get some MEK and that will fuse the plastic together. If you cant get that, superglue is your only option and as Mags said, anything you use is going to create a frosting effect anywhere you put it and the end result will be VERY ordinary, but there is light at the end of the tunnel.

As you have S1 lights, that's all red, maybe you could consider colour coding the outer red zone and then nobody would be any the wiser and the light area would only be the visible red.

Just a thought that might get your problem solved.

Cheers, D

r3volt21 Apprentice

r3volt21

Posted
  • Author
Posted

As you have S1 lights, that's all red, maybe you could consider colour coding the outer red zone and then nobody would be any the wiser and the light area would only be the visible red.

Just a thought that might get your problem solved.

Cheers, D

Thanks Dan didnt think of colour coding the whole light will give it a go lights didnt cost me anything so i have nothing to loose.

  • 2 weeks later...
Ghostrider Grand Master

Ghostrider

Posted
Posted
Hi,

I own a mr30 sedan and have my eye on some patrol 2.8 petrol extractors from a local wrecker and was just wondering if some1 could please tell me the amount I need to bring the flange back to make them fit.

I also scored a pair of s1 red on red hotplates for it for free from a friend who wrote his off they have a chunk missing right at the top of the left one and i wouldnt worry as its hardly noticable when on the car but they get water behind, I was just wondering if anyone knows what i could repair this with doesnt have to look that great as i want them in more to make sure i like that style before tracking a good cond set down.

Thanks in advance,

Paul.

Paul,

You might be interested in these?

The left appears ok with a chip out of the right so you could end up with a good set for a little money.

http://cgi.ebay.com.au/DR30-tailights-RARE...=item3caef398c5

Cheers, D

jrh001 Proficient

jrh001

Posted
Posted
I've seen those lights in person, i've been to that guys place to get some R31 Ti rims.

They looked fine to me, Chip is quite small 2cmish.

2cm sounds like a fair-sized chip. That's big enough to be called a chunk. Right-hand tail light looks a bit odd in the eBay pic, centre line doesn't seem straight.

JH

Ghostrider Grand Master

Ghostrider

Posted
Posted

Try these on Import Monster, but only 8 hours to go and no bids;

http://www.importmonster.com.au/view?url=h...&title=DR30

http://www.importmonster.com.au/view?url=h...&title=DR30

or these with 3 days to go and no bids;

http://www.importmonster.com.au/view?url=h...&title=DR30

or these with 4 days to go and no bids;

http://www.importmonster.com.au/view?url=h...e=M%20DR30%20Dr

Cheers, Dennis

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
×
×
  • Create New...