Jump to content
SAU Community

Recommended Posts

hey all, im new to this site & skylines

i recently bought a R33 GTS4 paid about 3500 for it.

i was just wondering is there a way to disable the attesa system?

and then simply just plug it in again?

or is this only the R32's?

any feedback would be greatly appreciated:)

thanks

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/
Share on other sites

you cannot just pull out a fuse like in the 32's. this is because their system was electrical and the 33's are hydrological.

You can drain the resovior in the boot but the safest thing to do is take out the front drive shaft.

BTW, how did you manage a 33 gts4 for 3.5k? is it damaged?

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5356095
Share on other sites

The caniser in the boot runs down to the actuator on the O\S\R of the car, it pumps fluids to the transfer case and when the slip light is activated it then runs too the rear diff and is pumped around there aswell, then back too the canister. It does this because it is a high pressured pump that activates clutch packs in the transfer case, this is how the attesa system works. Do not take the fluid out of the clutch packs with be distroid and you will have to spend a lot of money and all the parts with be EX jap.

The fluid is a ATF fluid, at nissan we sell nissan Matic D which is what they used stock.

You can take the front propeller shaft out but thats it.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357381
Share on other sites

how would i pull out the shafts? just pull them out

your only taking out the front shaft.

It is located under the car more towards the drivers side next to the gear box area.

there are four bolts that attach it to the car, they are in pricks of a position to get off...

the thing i do is, move one bolt at a time to the best position possible for you to reach by rolling the car, undo it and take it off, roll your car a little back or forward so the next bolt is in the same position and repeat.

when you get good at it, you can have it off in 10-15 mins if that....

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5357421
Share on other sites

As said before.

You can only disconnect the 4wd system in the R32's electronically.

In the 33 and 34 you must remove the front drive shaft.

This is the shaft from your transferbox (the thing hanging off the drivers side of the gearbox) going up to the front diff.

Link to comment
https://www.sau.com.au/forums/topic/329610-gts-4/#findComment-5359314
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
    • Thanks guys - I have been overseas for a hectic many weeks , so haven't had time to chase any of these up.  Some of the suggestions are for 4.1 ratio, which I already have, and a 3.5 at Lonsdale, which is also too tall.  Really looking for 3.9 or even a 3.7 LSD, either with M12 bolts. Will look some more.  
×
×
  • Create New...