Jump to content
SAU Community

Recommended Posts

Skyline R33 GTST

Factory 5 speed Manual

Factory Turbo

Factory side mount intercooler setup

17" alloy rims with new tyres

235/45R17 on front

255/45R17 on rear

Electric sunroof

Electric windows

Electric mirrors

Aftermarket Dump pipe

Aftermarket exhaust(lightly bigger then factory but still nice and quite to advoid police problems and great for driving in city traffic and highway with no exhaust droaning)

Genuine Nissan Skyline floor mats

Crack free dash (Perfect Condition)

Car alarm fitted with 2 remotes

retrimed leather interior (red and black) showing age (rear seats in center stiching spliting)

GTR body kit

HKS turbo timer

Nismo strut brace (front)

Slotted rotors on front and rear

Pod filter(getting little dirty needs clean)

192,000km on cluster

Factory engine and box nothing special done!

To do for roady

Clutch slipping on boost (Can replace clutch with Excedy HeavyDuty clutch and machine flywheel and new gearbox oil for $500 on top of sale price) I am a nissan mechanic so you dont have to worry about poor workmanship during clutch replacement.

Front bar cracked (car repair for $200 which is fibreglassing whole lower section of front bar and repair cracks and repaint whole bar)

Rev counter(tacho) inop (can get operating again for $100 May require cluster and speed sensor which ill cover costs)

Steering wheel (steering wheel is peeling) (can replace with legal condition one for $70)

After all these repairs are done i can supply a roady for no extra costs!!!

$6500

Vehicle is located on brisbane northside(Burpengary)

if you have any questions plz call or txt me!

0416 913 010 Jason

post-76901-1284607120_thumb.jpg

post-76901-1284607125_thumb.jpg

post-76901-1284607129_thumb.jpg

post-76901-1284607133_thumb.jpg

post-76901-1284607137_thumb.jpg

post-76901-1284607143_thumb.jpg

post-76901-1284607151_thumb.jpg

post-76901-1284607163_thumb.jpg

post-76901-1284607168_thumb.jpg

post-76901-1284607172_thumb.jpg

post-76901-1284607176_thumb.jpg

post-76901-1284607180_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/337033-skyline-r33-gtst-white-turbo-manual/
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...