Jump to content
SAU Community

Xforce Varex Cannon

ashneel
 Share

Recommended Posts

ashneel Grand Master

ashneel

Posted
Posted

have for sale Xfoce Varex cannon muffler

3" inlet with flange and 4" tip

as new condition. no dents or scratches. comes will all connections and adjustable hanger and 2 remotes.

these retail for over $400 new +postage. im looking for $300 and will post anywhere in Aus if YOU pay for postage (shouldnt be anything more then $30)

ta

Ash

Link to comment
https://www.sau.com.au/forums/topic/339879-xforce-varex-cannon/
Share on other sites
ashneel Grand Master

ashneel

Posted
  • Author
Posted

hasnt been on my car yet. i bought it but never installed it. but the car it came off had it fitted for about 2-3 months then seller went for a different set up.

starscream_r32 Collaborator

starscream_r32

Posted
Posted
hasnt been on my car yet. i bought it but never installed it. but the car it came off had it fitted for about 2-3 months then seller went for a different set up.

so i assume the valve works 100%?

did u get to test it?

cheers

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • Pac
      The New Official S A U - N S W Spotted Thread

      By Pac · Posted

      I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • Komdotkom
      NC MX5

      By Komdotkom · Posted

      The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Dose Pipe Sutututu
      Intercooler Choice

      By Dose Pipe Sutututu · Posted

      Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...