Jump to content
SAU Community

Recommended Posts

Howdy guys, Got a late model C33 Laurel halfcut here.

I've pulled most of the shit I need.

Front guards

$100 pr

Bumper

$75

Bonnet

$50

Headlights

$100 set

Engine bay panels

$Make an offer on what you need

Wipers + Shrouds

$50

Electrical wiring behind dash #some parts modified

$Make an offer on what you need

Crossmember + Sway bar + Steering Rack

$350

Suspension parts, front

$Make an offer on what you need

Unknown brand coilovers, red, base height adjustable with camber tops, #condition unknown

$150

Air con parts (inc ducting, wiring, relays, etc)

$Make an offer on what you need

Lower Dash parts + Centre console (lower only, no top half, it shift boot, cd player surround, etc)

$Make an offer on what you need.

Anything else you need that I've forgotten, just ask.

Panels are a very dark green kind of color. Interior is dark brown.

Has some other goodies like a HKS Turbo Timer, HKS Mushroom filter, etc

Some aftermarket blow off valve, it's huge, and red.

Hit me up quick people.

Need this halfcut gone pretty quickly as it's at my mates place, not mine.

If somebody wants the whole cut to make a BBQ or something, lemme know.

Pics on request.

Shipping out of Perth.

Nic

0431 598 320

Stuff NOT for sale

Motor

Gearbox

Intercooler setup.

Dash

Brakes (BM50 FTW :D)

Link to comment
https://www.sau.com.au/forums/topic/340744-c33-laurel-halfcut-left-overs/
Share on other sites

Would you have any of the factory dash switches (eg sport/comfort etc) let me know what ones your dash came with and if you want to sell them.

Cheers, Dan

Dan do u need ceffy ones ? Iv got some in my ceffy I'm home as of tommorow night and I'm in perth. If nic doesn't have them that is.

Pm me if nic doesn't have any and or if my ones suit ur needs.

But please wait for nics reply as I do not want to steal a sale from him.

Ranga

No none of those switches sorry.

I'm keeping the Laurel dash and wiring loom behind it as upgrade for Cefiro.

Have hubs + LCA but you'll need to ask dori_FC if he can part those, he is probably taking the entire halfcut so need to keep it rolling until it makes it to his house I guess.

Stay tuned guys - I will get back to you all I'm just stupidly busy at the moment.

Cheers

Nic

Bonnet on hold, if it lines up alright on the Ceffy I was planning on turning it panda.

Corner lights might not have, still waiting on guards to be delivered (possibly with bumper).

No grille here but might be delivered (doubt it)

Do you want reo bar as well or just bumper? Got a fairly new reo bar on it, still has nissan genuine parts sticker on it.

Toffy How badly do you want that guard?

That release cable is very stiff, but havent removed it yet, it might just be jammed somewhere.

Sorry for the wait guys, just bear with me.

I've got next week off work, i'll properly dismantle it and go get shipping quotes.

HKS filter gone.

Air con ducting gone.

HKS turbo timer here has adapter to suit R32, and ignition switch to suit.

I'll chop body plug so you can rewire it in if somebody wants it all.

Edited by Nic_A31

not that badly (the guard), i could repair mine quite easily if someone else needs it real bad :) , let me know how you go with the bonnet release cable :rofl2: oh and could you post up a pic of the front bar?

Edited by toffy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...