Jump to content
SAU Community

Recommended Posts

Item: Volk TE37 18x9.5 +12 in Bronze. Pair only.

Location: Brisbane (will ship)

Item Condition: Very Good Condition

Reason for Selling: (Im a big bitch) This is a spare pair I have, was going to use them as my boss skid pair but I could use the cash right now, fml.

Price and Payment Conditions: $1500

Extra Info: Real TE37's, light as s***, good size and offset, increase the size of your e-wang, will suit posers and actual drivers

Contact Details: PM, reply or 0422 091 381

te1.jpg

te2.jpg

te3.jpg

te4.jpg

te5.jpg

Edited by Tayno
Link to comment
https://www.sau.com.au/forums/topic/340864-te37s-18x95-12/
Share on other sites

Hi mate

in the pics, it looks in some like these have been painted bronze rather than being the anodised finish - it could just be the light, but there looks to be a sort of glossy reflection that's not normally there on the anodised finish?

Cheers

Aaron

Item: Volk TE37 18x9.5 +12 in Bronze. Pair only.

Location: Brisbane (will ship)

Item Condition: Very Good Condition

Reason for Selling: (Im a big bitch) This is a spare pair I have, was going to use them as my boss skid pair but I could use the cash right now, fml.

Price and Payment Conditions: $1500

Extra Info: Real TE37's, light as s***, good size and offset, increase the size of your e-wang, will suit posers and actual drivers

Contact Details: PM, reply or 0422 091 381

te1.jpg

te2.jpg

te3.jpg

te4.jpg

te5.jpg

Link to comment
https://www.sau.com.au/forums/topic/340864-te37s-18x95-12/#findComment-5503373
Share on other sites

Thats correct Aaron. This pair has been refinished in bronze to match a set of bronze te37's which I already have. As the lip on bronze te37s is diamond cut and then anodised it is almost impossible to replicate. Therefore, these are just all one colour.

Link to comment
https://www.sau.com.au/forums/topic/340864-te37s-18x95-12/#findComment-5503994
Share on other sites

Thats correct Aaron. This pair has been refinished in bronze to match a set of bronze te37's which I already have. As the lip on bronze te37s is diamond cut and then anodised it is almost impossible to replicate. Therefore, these are just all one colour.

No probs mate, I was looking for a pair with the original finish - fyi - we have a place in Melb called Wheel Solutions that uses a candy paint on the lips to get rid of rash and you can't tell it's been done - if it ever happens again to you, you don't need to paint the whole wheel :)

Link to comment
https://www.sau.com.au/forums/topic/340864-te37s-18x95-12/#findComment-5504022
Share on other sites

No probs mate, I was looking for a pair with the original finish - fyi - we have a place in Melb called Wheel Solutions that uses a candy paint on the lips to get rid of rash and you can't tell it's been done - if it ever happens again to you, you don't need to paint the whole wheel :)

Yea no worries. Thanks for the tip.

Link to comment
https://www.sau.com.au/forums/topic/340864-te37s-18x95-12/#findComment-5504096
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...