Jump to content
SAU Community

Velo Milano Racing Seats Pair

R32Dreamer
 Share

Recommended Posts

R32Dreamer Community Regular

R32Dreamer

Posted
Posted (edited)

Hello ALL,

I have up for sale a Pair of Velo Racing Seats, FIA and ADR approved Milano's.

Seats are in excellent condition with no holes, rips or signs of wear. They came with a previous car I purchased that was being built for amature drag racing...

Seats are amazingly comfortable and would suit anyone building a full blown race car too a daily driver that might see a bit of track action.

Of course the best thing about the entire Velo range is they are ADR approved, so no worries from the police.

I am looking to sell them as a pair which will make them cheaper for the buyer.

Price is FIXED because of the obvious value in these seats.

$850 for the pair or $450 each

post-15679-1287377524_thumb.jpg post-15679-1287377548_thumb.jpg post-15679-1287377580_thumb.jpg

post-15679-1287377605_thumb.jpg post-15679-1287377798_thumb.jpg

Contact Aaron via PM or for a quicker response call/SMS me on 0438 86 08 07

Thanks

post-15679-1287376159_thumb.jpg

Edited by R32Dreamer
Link to comment
https://www.sau.com.au/forums/topic/340889-velo-milano-racing-seats-pair/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...