Jump to content
SAU Community

Recommended Posts

hey guys.... i have heaps of gauges in the boxes.. NEW... that i want to get rid of super cheap

i have :

DRIFT crystal series....

-air fuel ratio 52mm

-oil temp 52mm

-5" boost gauge

-boost 52mm

-vacuum 52mm

-volt 52mm

-water temp 52mm

also have ignite series 2....

-air/fuel ratio 52mm

-oil pressure 52mm

-oil temp 52mm

-vacuum 52mm

please let me know what you want and i will give you a price.... but as a rough idea.... 52mm will be about $50 each approx!

thats pretty dammn cheap! :)

Link to comment
https://www.sau.com.au/forums/topic/342989-gauges-all-sorts-new-in-boxes-cheap/
Share on other sites

some pics and prices would help...

tell me what gauges your after and ill let you know how much ... and as for pics .. i can email them to you if you would like

oh and by the way everyone.... i have a wrx '01 - '03 cat back stainless drift exhaust for sale too ... $500 mint condition

Edited by roney1gtr
do they come with everything needed or just gauges alone?

i need

-boost 52mm

-water temp 52mm

-oil pressure 52mm

-oil temp 52mm

[email protected]

thanks

the gauges are in the boxes with everything you need !!! ill send you pics and prices

5 of each? Sounds like a trader ad.

Please consult the thread below if you wish to look into becoming a registered trader:

http://www.skylinesaustralia.com/forums/Bu...se-t294953.html

Closed.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...