Jump to content
SAU Community

Antilock Warning Light Turns On And Off

HR32GTS 4DOOR
 Share

Recommended Posts

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
Posted

Ok I just bought an R32 GTS with abs brakes,

It had hardly any brake fluid left and the antilock light was always on. So I blead the whole brake system calipers and abs thingy. The brakes work really well now but the anti lock light turns off and on whilst I'm driving it.

I gotta take it to regency in the next week or so, will they defect the car for that?

Anyone have any ideas???

GTRPowa Rising Star

GTRPowa

Posted
Posted (edited)

Weird I had the same problem a few months ago. My brakes were leaking at the ABS because of a poorly tightened flare nut. Before I noticed the issue I had to slow rather quickly, and the light showed up as I felt the ABS startting to operate. All was well though, brakes still were fine, fixed the leak, bled the brakes, and had the light come on randomly during a drive (this lasted for a few weeks, driving twice a week). Diagnostics showed the ABS had a problem with it's solenoid. After a few weeks it stopped by itself, I've always assumed it was an air pocket. A recent bleeding (only at the calipers) supported my theory since a little more air came out after a few pumps. Since then it's been fine, no leaks, no air, no lights. Hope it shed's light.

For regency, remove bulb, but being me, I'd always make the assumption a good regency worker would check to see if the ABS lights up when the ignition is first turned to ON. If I had to test 'the operation of fitted ABS' it's be one of the things I'd check.

Edited by GTRPowa
dorifticon Community Regular

dorifticon

Posted
Posted

My abs light came on the other day, all fluids were full so I examined the fuse in the driver's side engine bay, it looked fine. Then I pulled apart the connectors on the passenger side near the ABS module, thinking they might be corroded or soemthing, but they looked ok. Then I pulled the relays inside the actual black box.

Started it up and light is off.

Maybe as a first step clean all the little electrical contacts etc and see if it helps>? Also do a search on "abs light" the solution can be relativley simple or as serious as getting a new motor unit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...