Jump to content
SAU Community

Recommended Posts

Cusco zero 2E coilovers

suit r32

8/6 spring rate.

dont less than 5000 km. pretty much brand new.

2 way height adjustable

$1400

postage 30-60 bucks oz wide

DSCN1050.jpg

DSCN1051.jpg

DSCN1053.jpg

DSCN1052.jpg

Cusco zero 2R rear coilovers

suit r34 gtt, r34 gtr, r33 gtr, r32 gtr

mint contition, barely been used at all. like new

6 way damper adjustable (might be 5, ill check though)

2 way height adjustable

6kg spring rate.

$700

DSCN1037.jpg

DSCN1039.jpg

Cusco caster rods

suit r32, s13, a31, 180 ect

suit gtr's with spacer on 1 side

perfect working order.

$220

DSCN1047.jpg

DSCN1048.jpg

rb25 manifold

came with a car i bought, its off an rb25. i have no use for it.

$150

DSCN1049.jpg

mackie

0422 905 956

Edited by flame_this
Link to comment
https://www.sau.com.au/forums/topic/351089-cusco-coilovers-basically-new/
Share on other sites

the top set of coilovers is for r32 gtst models.

happy to mix the sets if a set of coilovers is required for r34/ gtr, r32 gts4 or any other models.

best just to pm or contact me on the number though.

cheers

R33 rears go nowhere near fitting R32s, that pair of rears will be about 6 inches too long for R32, you can see it from the photos... I had to give away a shit hot set of Bilsteins for exactly that reason

R33 rears go nowhere near fitting R32s, that pair of rears will be about 6 inches too long for R32, you can see it from the photos... I had to give away a shit hot set of Bilsteins for exactly that reason

yeah... there a completely different coilover, didnt imply nething here suited r33 other than the r33GTR rear coilovers there which suit r34 gtt and r34 GTR models.

have an r33 set in a different set if anyones interested.

the r32 cusco zero 2 E's are sold pending payment.

r34 GTT, r33/r34 GTR rear cusco still available.

Edited by flame_this
  • 11 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...