Jump to content
SAU Community

Recommended Posts

Hi, up for sale is my 1999 V-spec R34 GTR in showroom condition.

Engine is 5000km old with 2000 of those going through stages of running in. Never tracked.

Currently has 600.7rwkw on e85, with saved tunes for both bp ultimate and e85

All aftermarket parts used were new.

Engine Mods include:

- 2.7 l stroker kit with billet conrods and crankshaft

- HKS T51R Kai Single Turbo conversion

- Extended sump

- Nitto oil pump

- n1 water pump

- ARP bolts

- ACL race series bearing

- ATI harmonic balancer - 1000hp

- Full Port and polish of head

- Mines Triple Flow cam cover baffle plates

- Tomei procams

- Tomei valve springs and retainers

- Tomei Valve lifters

- Tomei gasket kit

- Supertech 1mm oversize valves

- Billet twin entry fuel rail

- Sard Big capacity Fuel Pump

- 2 bosch 044 external fuel pumps and custom surge tank

- Adjustable Fuel pressure regulator

- Bosch 1680cc injectors

- Nismo twin plate coppermix clutch

- Greddy intercooler

- Greddy hard piping kit

- Greddy oil cooler

- PWR Radiator

- Vipec ECU

+custom piping, hosing and carbon fibre bits

Suspension & Brakes:

-Brembo Gran Turismo Front big brake kit - not pictured

-Greddy coilovers

-Greddy in car electronic damper adjustment

-ARC racing stabilizers (swaybars) - Front and Rear

-Cusco camber adjustable rear upper arms

-Cusco front negative arms

Interior:

-Alpine 7inch double din head unit

-DLS 6.5in splits

-DLS 3 Channel Amp

-DLS Magnesium Sub

Also:

-Kakimoto stainless steel exhaust

-Rays Volk GT-C face 2 19x10.5 rims

-Nismo z-tune body kit

-Nismo 320km/h speedo with 9k km on it ... Stock one will also be given

-Nismo L.E.D tail lights

Huge amount of money has been thrown at this car but time to move on and start a new project.

SAU Price: $78000

Please genuine enquiries only, pm me as i do not check threads often

post-48719-0-92653000-1296114229_thumb.jpg

post-48719-0-95840000-1296114251_thumb.jpg

post-48719-0-16851200-1296114266_thumb.jpg

post-48719-0-83459800-1296114279_thumb.jpg

post-48719-0-06549100-1296114298_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/351885-r34-gtr-v-spec/
Share on other sites

  • 2 weeks later...
  • 3 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...