Jump to content
SAU Community

Recommended Posts

Got some stuff here for sale that i dont need.

S15 Apexi PowerFC (PFC-SR2018) + New EL LED Hand Controller, (PowerFC Used, Hand Controller still new just took out of the box to check if it works with my pfc.) = $1000ono Posted Aust wide.

OEM S14/S15 VCT Solenoid Valve, Brand New in box = $150

Used Bride Seat Rail Driver side N049RX, Fits Ergo2, Brix 2 etc.. = $150ono

Set of BRAND NEW Genuine S15 Silvia Badges(Silvia, Lightning S, 2x Spec-R) = $120 ono

Pics Will Be Up Tomoro

Contact Via, PM Or SMS Tam on 0423506186

S15 Apexi PowerFC (PFC-SR2018) + New EL LED Hand Controller, (PowerFC Used, Hand Controller still new just took out of the box to check if it works with my pfc.) = $950ono Posted Aust wide.

WILL SEPARATE THE EL LED HAND CONTROLLER (WILL WORK WITH ANY PFC EXCEPT FOR TOYOTA JZX100 AT MODEL) Model No. 415-A030 Universal, STILL NEW WITH BOX. FOR $430 POSTED

UPDATED!!!!

S15 Apexi PowerFC (PFC-SR2018) + New EL LED Hand Controller, (PowerFC Used, Hand Controller still new just took out of the box to check if it works with my pfc.) = $1000ono NOW ONLY $850 POSTED AUSTWIDE.

OEM S14/S15 VCT Solenoid Valve, Brand New in box = $150 NOW ONLY $100 Posted

Used Bride Seat Rail Driver side N049RX, Fits Ergo2, Brix 2 etc.. = $150 NOW ONLY $100 + Delivery TAKE IT AWAY!! 100% Genuine.

Set of BRAND NEW Genuine S15 Silvia Badges(Silvia, Lightning S, 2x Spec-R) = SOLD!!!!!

Used S15 Stock T28 Rubber Intake Pipe = $10

S15 Airbox Snorkel Only = $20 (Few Scratches here n there)

Other Stuff:

Used Logitech X530 5.1 Surround Speakers = $50 (100% Good Working Condition 2 Speakers Got rips through the mesh outside the speaker doesnt affect anything)

ASRoCK X58 Extreme Motherboard = $150 (Almost New Condition Used for 1 month then upgraded to Asus Rampage Extreme 3) AsROCK X58 Extreme MB Comes With Box + All Accessories.

Pics uP Soon

Contact Via, PM, Email: [email protected] Or SMS Tam on 0423506186

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...