Jump to content
SAU Community

Fs: Series 1 R33 Parts: N1 Bonnet Lip, Lenso Wheels, Gts-4 Brakes, Rear Seats, Fibreglass Front Grill, Rear Mats, Mirrors, Zex Purge Kit


Recommended Posts

Wheels:

Lenso GF7 Black centre with polished lip

18 x 7.5 all round with multi stud 4x100 or 4x114.3

$550 including current tyres

(pickup only)

N1 Bonnet Lip (White) $40

Front Grill (Series 1) unpainted changed my mind and bought a carbon one $40

Rear Mats minus centre one $30 Good condition as rarely had passengers in the rear

Rear Seats $60 Good condition same as above rarely had passengers

Mirrors Series 1 (Not a standard colour would need to be painted) $60

'95 GTS-4 Brakes, calipers everything included as I upgraded to GTR brakes for 5 stud conversion. Make an offer on these

Zex Nitrous Purge Kit (Brand New sealed in box)

Setup includes:

10lb Nitrous Bottle (Empty)

Bottle Clamp

Braided Lines

Purge Solenoid

Also purchased additional set to create a dual vent purge kit worth $120 alone

Green LEDs included

Cost me $550 delivered from USA, selling for $350.

Still availble:

R33 Series 1 Rear Seats good condition $50

R33 Side Mirror (Custom colour so would need to be repainted) $60 both or $40 each

R33 Series 1 Front Grill Fibreglass unpainted $40

R33 GTS-4 brake setup, everything, have upgrade to GTR 5 stud (make an offer)

R33 Rear Floor Mats $20 minus centre mat

Zex Nitrous Purge Kit $350

Yeh still got the wheels, but your car was 5 stud, these wheels are 4 stud...wouldnt fit your GTST.

Still for sale are:

ZEX Nitrous Purge Kit $350

R33 Series 1 Rear Seats good condition $50

R33 Side Mirror (Custom colour so would need to be repainted) $60 both or $40 each

R33 Series 1 Front Grill Fibreglass unpainted $40

R33 GTS-4 brake setup, everything, have upgraded to GTR 5 stud (make an offer)

R33 Rear Floor Mats $20 minus centre mat

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...