Jump to content
SAU Community

Recommended Posts

I have for sale a few items lieing around that i dont need and might be of some use to others

I can post most stuff except the weights and postage will be calculated depending on the buyers location

1- Apexi pen turbo timer, black, it was in working condition when i removed it from a previous car of mine $40 plus $8.00 postage to anywhere in australia

DSCF6605.jpg

2- Turbosmart boost tee, manual boost controller, it was not needed in my old r32 as i ran it stock so i pulled it out, works fine, has a scratch as seen in picture due to where it sat, $30 plus $8.00 postage anywhere in australia

DSCF6613.jpg

3- R32 fuel injector rail, came with a stock fpr i bought and i never needed it $20.00 plus $10.00 postage anywhere in australia

DSCF6606.jpg

4- Unknown brand fpr (fuel pressure regulator), it came with my r32 and it wasnt needed in a basically stock setup so it was pulled out $30 posted

DSCF6615.jpgDSCF6614.jpg

5- R32 Digital Climate control in good condition $50.00 plus $8.00 postage anywhere in australia

DSCF6608.jpg

6- Z142A VR4 galant oil filter new in box never been used, $5.00 pick up or $10.00 posted

DSCF6610.jpg

7- Walbro gss342 fuel pump, genuine, it was removed from a r32 to diagnose a issue but found out it was a spark issue, $90.00 posted aus wide

DSCF6607.jpg

8- Gym training weights, sand filled, 4x10pounds and 4x 15pounds(not sure what that is in kg's but its around just above half, so over 50kg's in weights

I cant post these as it has alot of weight in it, i paid $60.00 about 3 years ago, they are in used condition with usuall wear and tear and will sell them for $30.00

DSCF6617.jpg

9- Hand ratchet tie down, 50mm x 9metres, load capacity is 2500kg's, brand new and never been used, the brand is - Secure A Load. $20.00 plus $10.00 posted aus wide

DSCF6616.jpg

10- HUGE Tarpaulin, brand new never been used, it has price on it still, measures 600cm x 900cm, i paid $34.99, ill sell it for $25.00, i might post but it does have some size about it so might cost abit

DSCF6618.jpg

All items can also be picked up from St Clair which is in between Blacktown and Penrith

Any questions call me on 0421735661

Thanks Andy

No worries mate will you pick it up or want it posted? I noticed you are newcastle. i might be going to gosford tommorrow night to visit family so if u want can pick it up there

Thanks Andy - 0421735661

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...