Jump to content
SAU Community

A Few Bits And Pieces, R32, General Stuff Etc For Sale

andyvr4
 Share

Recommended Posts

andyvr4 Enthusiast

andyvr4

Posted
Posted

I have for sale a few items lieing around that i dont need and might be of some use to others

I can post most stuff except the weights and postage will be calculated depending on the buyers location

1- Apexi pen turbo timer, black, it was in working condition when i removed it from a previous car of mine $40 plus $8.00 postage to anywhere in australia

DSCF6605.jpg

2- Turbosmart boost tee, manual boost controller, it was not needed in my old r32 as i ran it stock so i pulled it out, works fine, has a scratch as seen in picture due to where it sat, $30 plus $8.00 postage anywhere in australia

DSCF6613.jpg

3- R32 fuel injector rail, came with a stock fpr i bought and i never needed it $20.00 plus $10.00 postage anywhere in australia

DSCF6606.jpg

4- Unknown brand fpr (fuel pressure regulator), it came with my r32 and it wasnt needed in a basically stock setup so it was pulled out $30 posted

DSCF6615.jpgDSCF6614.jpg

5- R32 Digital Climate control in good condition $50.00 plus $8.00 postage anywhere in australia

DSCF6608.jpg

6- Z142A VR4 galant oil filter new in box never been used, $5.00 pick up or $10.00 posted

DSCF6610.jpg

7- Walbro gss342 fuel pump, genuine, it was removed from a r32 to diagnose a issue but found out it was a spark issue, $90.00 posted aus wide

DSCF6607.jpg

8- Gym training weights, sand filled, 4x10pounds and 4x 15pounds(not sure what that is in kg's but its around just above half, so over 50kg's in weights

I cant post these as it has alot of weight in it, i paid $60.00 about 3 years ago, they are in used condition with usuall wear and tear and will sell them for $30.00

DSCF6617.jpg

9- Hand ratchet tie down, 50mm x 9metres, load capacity is 2500kg's, brand new and never been used, the brand is - Secure A Load. $20.00 plus $10.00 posted aus wide

DSCF6616.jpg

10- HUGE Tarpaulin, brand new never been used, it has price on it still, measures 600cm x 900cm, i paid $34.99, ill sell it for $25.00, i might post but it does have some size about it so might cost abit

DSCF6618.jpg

All items can also be picked up from St Clair which is in between Blacktown and Penrith

Any questions call me on 0421735661

Thanks Andy

andyvr4 Enthusiast

andyvr4

Posted
  • Author
Posted

No worries mate will you pick it up or want it posted? I noticed you are newcastle. i might be going to gosford tommorrow night to visit family so if u want can pick it up there

Thanks Andy - 0421735661

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...