Jump to content
SAU Community

Recommended Posts

Have any of you guys used nibblers for sheet steel and aluminium - and what do you think of them?

In particular talking about the drill attachment type: http://newstyledirect.com.au/store/images/D/nibbler-pic3.jpg

Any advice on using one to make a straight cut, aside from obviously clamping a guide rail?

Also, it's Friday. cheers.gif

Link to comment
https://www.sau.com.au/forums/topic/358659-nibblers/
Share on other sites

  • 3 months later...

They are a god send, especially when making long cuts and usually wind up alot neater than using Snips, theyu do come at a price though i think a set of electric makita ones would set you back around 600 bucks although im not too sure about they pneumatic ones I think they may be considerably cheap. We prodominently use battery powered ones on site but the price for those escalates again.

they will usualy cut upto about 1.2mm stainles steel and as long as you have a steady hand will do a very nice job

Link to comment
https://www.sau.com.au/forums/topic/358659-nibblers/#findComment-5885553
Share on other sites

When u are fitting sunroofs the are the only way too cut a hole in the roof skin because they leave very little damage, I only use a guide line and with practice u can get it pretty well spot on everytime just takes a steady hand. I've used numerous battery operated and corded brands they are all pretty well similar but in terms of regular use you get what u pay for, Bosch is my favorite ATM

Link to comment
https://www.sau.com.au/forums/topic/358659-nibblers/#findComment-5886191
Share on other sites

  • 4 weeks later...

I ended up buying some $50 cheapie from bunnings that attaches as a drill piece - aside from the drill getting in the way, it was fairly easy. Must be high on crack though cause my lines were pretty shaky. Also found out that using some lube to cool the nibbler is the way to go, or it gets very hot and if you're going through aluminium the pieces will start sticking in the nibbler.

I was cutting sheets of ally and ended up using a grinder and zapping it on some steel to clean out the ally gunk every few metres. Nibbler is still great though and has a permanent place in my workshop.

I'm still picking half-moon pieces of aluminium out of the bottom of my shoes.

Link to comment
https://www.sau.com.au/forums/topic/358659-nibblers/#findComment-5923128
Share on other sites

  • 2 weeks later...

Used a nibbler pretty much daily at my work but as you said the half moon cut offs are annoying as well and we would spend more time in clean up then actually doing a job. If its non complicated straight lines your mainly doing (which is what we normally for access panels into sheet metal at work) we swapped over to some straight shears which means no more half moon cut outs just long curly pieces of metal from the line you cut.

JS1601_zoom.jpg

Link to comment
https://www.sau.com.au/forums/topic/358659-nibblers/#findComment-5941708
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...