Jump to content
SAU Community

Recommended Posts

Ok so I went down to the shops a couple of nights ago and parked up. Came out 15 minutes later and...

Disabled Immobiliser

Turned key to ACC to let fuel pump prime

Cranked over once with the standard worn starter motor crackle but she didn't fire up

After I cranked her, all the accessory lights that normally illuminate at ACC slowly faded to nothing and all electrics in the car were non-operational.

I thought the problem was with the battery (and still think it could be) so I tried jumping her with the clamps attached to the battery (normal jump start practice) but got nothing.

After about 10 minutes of connection to my mates VE SS with him giving a good rev every now and then, I got the dash lights on and got the car started.

Parked her up at home and didn't touch her until the following day when I noticed the immobiliser light flashing.

I turned the immobiliser off with the key and cranked her over and she fired up as normal (starter motor didn't even complain).

Then went for a short drive and came back and parked her up.

After two hours I went to fire her up again and as soon as i unlocked her she went completely dead again

Got my mates car connected again but this time I couldnt get her to crank with the battery connected. I had to disconnect the battery and jump her straight from the clamps and this worked instantly.

My problem now is that I don't know what is failing. I haven't known an 8 month battery to f**k up like this and be seemingly perfect sometimes and then dead other times.

I'm starting to think that my problem could be in the key barrell or with the immobiliser. Sometimes when I turn the key to accesories I'll here the pump struggle to prime (lower whine than normal) and then after a couple of seconds spring back to what could be described as the normal fuel pump whine.

Car's off to xpeed tomorrow but I'm wondering what I could be up for?

James

Link to comment
https://www.sau.com.au/forums/topic/359121-startingelectrical-issue/
Share on other sites

Check that there's a good earth to the negative side of your battery and to your motor, I had similar issues and ended up being a loose negative lead where it earthed out to the body if the car. Also make sure you have good contact on the terminals of your battery (little bit of boiling water and a wire brush). Make sure they are tight and free from corrosion. Hope this helps

  • 2 weeks later...

Check that there's a good earth to the negative side of your battery and to your motor, I had similar issues and ended up being a loose negative lead where it earthed out to the body if the car. Also make sure you have good contact on the terminals of your battery (little bit of boiling water and a wire brush). Make sure they are tight and free from corrosion. Hope this helps

Well yeah you were correct with everything man.

One earth wire was loose, battery clamps were corroded and the battery itself wasn't tied down.

Car now has none of the symtoms I first listed!

Cheers bro!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...