Jump to content
SAU Community

Recommended Posts

I have an issue with my r33 rb25de ! :(

So basically when the engine is COLD and i start driving it. In first and second gear when my revs are low the car makes a whining noise (i THINK when im holding down the clutch and accelerating). Realyl worries me, sounds like theres a major issue.

Any help will be appreciated!@

Link to comment
https://www.sau.com.au/forums/topic/362649-r33-whining-noise/
Share on other sites

If the clutch is worn chances are the thrust bearing is worn to,

Before I changes my clutch yhe bearing was really loud

As asked before does the noise go away when the clutchpedal is all the way to the floor?

Also you said it only happens when it's cold If

The sound goes away when the cars warm it could be a sign of a gearbox problem

Edited by stig mick

Hmmm not really sure then you might want to have that looked at by someone who's know what they are doing could be a gear box problem,

Luckily it's not a hugely expensive job to swap it over if your getingthe clutch changed it would cost any extra in labour, it's just a natter if find a decent condition reasonably price gear box

Im not 100% sure. It happens when the clutch is engaged + im accelerating. If i just hold the clutch and dont touch the gas i dont think it makes any noises.

Next time see if it is in all gears except for forth... Forth is the only gear that doesn't put pressure on the cluster shaft bearings. Could also be your input shaft bearing. Both are very common noises on our gearboxes.

Are you sure it's the trust bearing?

I've never heard a thrust bearing that loud and Ive had 5 or 6 different make cars with a very worn or slightly worn thrust bearing

Not 100% but I've got a mate who's done 3 or 4 thrust bearings in the past and he's positive that's it. Did show up very suddenly and very loudly though. Need to get an expert's opinion.

It had run out of power steering fluid!

Dude not cool, check all fluids(under bonnet) every two weeks as a guide, more if you know you have problems that cannot be fixed for a while.

EDIT: Just sayin, not hatin.

Edited by Shazza24

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...