Jump to content
SAU Community

Recommended Posts

I have an issue with my r33 rb25de ! :(

So basically when the engine is COLD and i start driving it. In first and second gear when my revs are low the car makes a whining noise (i THINK when im holding down the clutch and accelerating). Realyl worries me, sounds like theres a major issue.

Any help will be appreciated!@

Link to comment
https://www.sau.com.au/forums/topic/362649-r33-whining-noise/
Share on other sites

If the clutch is worn chances are the thrust bearing is worn to,

Before I changes my clutch yhe bearing was really loud

As asked before does the noise go away when the clutchpedal is all the way to the floor?

Also you said it only happens when it's cold If

The sound goes away when the cars warm it could be a sign of a gearbox problem

Edited by stig mick

Hmmm not really sure then you might want to have that looked at by someone who's know what they are doing could be a gear box problem,

Luckily it's not a hugely expensive job to swap it over if your getingthe clutch changed it would cost any extra in labour, it's just a natter if find a decent condition reasonably price gear box

Im not 100% sure. It happens when the clutch is engaged + im accelerating. If i just hold the clutch and dont touch the gas i dont think it makes any noises.

Next time see if it is in all gears except for forth... Forth is the only gear that doesn't put pressure on the cluster shaft bearings. Could also be your input shaft bearing. Both are very common noises on our gearboxes.

Are you sure it's the trust bearing?

I've never heard a thrust bearing that loud and Ive had 5 or 6 different make cars with a very worn or slightly worn thrust bearing

Not 100% but I've got a mate who's done 3 or 4 thrust bearings in the past and he's positive that's it. Did show up very suddenly and very loudly though. Need to get an expert's opinion.

It had run out of power steering fluid!

Dude not cool, check all fluids(under bonnet) every two weeks as a guide, more if you know you have problems that cannot be fixed for a while.

EDIT: Just sayin, not hatin.

Edited by Shazza24

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...