Jump to content
SAU Community

Recommended Posts

is it possible that the ecu has a problem cause the car still runs and relay is working...or could the ecu say f**ked up relay before it will f**k up?^^

i gonna get a new relay the next days but i just don't understand this here :happy:

sombody an idea?

Edited by o0o

Some of the relays near the fuse cluster are the exact same plug type and numbers...should be for headlights / tail lights, etc,....ie not neccesary to run.

Swap the over see if that works.

Possible that the ECU is the problem....reset the ECU (clear stored codes) and see if the code returns.

What exactly is the problem and how did you test the relay?

Diagnosing the relay is pretty simple.

Turn the igniton on, if the fuel pump primes then it's doing the first half of its job,

Flick the starter motor over a couple of turns, if the fuel pump primes again, then it's doing the other half.

If it's not priming fuel, and the relay IS working fine (or you test out another relay and it still isn't pumping fuel), then you could have a short on your fuel cradle ('sender'), on the tank, or somewhere on the loom going to the relay.

Edited by Nic_A31

actually there is no problem,...it was just i had nothing to do lol :whistling:

i checked the ecu for some errorcodes and hoped for no errors^^

but then came error for the the pump relay...

i did what you said and exchanged the relay with a another from under the hood it works fine, with the new relay no errorcode...today i switched the old relay back in its old position and checked errorcodes again and now no error with the original relay?

its getting confusing >_<

as far the car runs without problems its ok for me:D

@btw big thx on nic...you already helped me on alot problems now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...