Jump to content
SAU Community

Recommended Posts

is it possible that the ecu has a problem cause the car still runs and relay is working...or could the ecu say f**ked up relay before it will f**k up?^^

i gonna get a new relay the next days but i just don't understand this here :happy:

sombody an idea?

Edited by o0o

Some of the relays near the fuse cluster are the exact same plug type and numbers...should be for headlights / tail lights, etc,....ie not neccesary to run.

Swap the over see if that works.

Possible that the ECU is the problem....reset the ECU (clear stored codes) and see if the code returns.

What exactly is the problem and how did you test the relay?

Diagnosing the relay is pretty simple.

Turn the igniton on, if the fuel pump primes then it's doing the first half of its job,

Flick the starter motor over a couple of turns, if the fuel pump primes again, then it's doing the other half.

If it's not priming fuel, and the relay IS working fine (or you test out another relay and it still isn't pumping fuel), then you could have a short on your fuel cradle ('sender'), on the tank, or somewhere on the loom going to the relay.

Edited by Nic_A31

actually there is no problem,...it was just i had nothing to do lol :whistling:

i checked the ecu for some errorcodes and hoped for no errors^^

but then came error for the the pump relay...

i did what you said and exchanged the relay with a another from under the hood it works fine, with the new relay no errorcode...today i switched the old relay back in its old position and checked errorcodes again and now no error with the original relay?

its getting confusing >_<

as far the car runs without problems its ok for me:D

@btw big thx on nic...you already helped me on alot problems now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...