Jump to content
SAU Community

Recommended Posts

Hey everyone, I'm putting this car up here for a mate. I've driven it, and I will say it changed my mind about the hondas. Never thought much of them because they were FWD, but this thing hauls ass. I would say you'd be hard pressed to find a quicker car that is P plate legal than one of these. It has an integra B18C Vtec engine in it, and it pulls very hard. Here are some pictures

genthumbsphp.jpg

CRX6.jpg

CRX5.jpg

CRX4.jpg

CRX3.jpg

CRX2.jpg

The list of mods are as follows:

I am selling my '89 Honda CRX,

it's lowered on king springs,

full CYBEX kit,

Hasport engine mounts,

Hondata200 ECU,

Recaro imitation bucket seats,

momo steering wheel

Rego. til Dec. 2011

No mechanical faults.

No Leaks.

Extremely Fuel efficient $35-40 to fill tank from empty (depending on prices) - 600km to a tank.

B18C VTEC!! VERY QUICK P PLATE CAR.

+ more.

$6000 NEGOTIABLE! Make on offer you never know.

Contact via PM on here, or ring/txt my mate on 0411 115 851 His name is Matt.

The car has been driven responsibly (my mate doesn't get up his car too much, I gave it a bit of stick for the 30 seconds that I drove it, it probably needed it to be honest haha) and serviced regularly.

Oh, and please disregard the fact that these photos are from Boost. He isn't the typical boost cruising wank, I just told him he will have more of a chance selling it if he exhausts every avenue possible.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...