Jump to content
SAU Community

Recommended Posts

1995 Nissan Skyline R33 GTR Series 1

147,000 kms

5 speed manual

Price: $30,000 ono

Contact: Andrew 0412773767

Reason for selling is because I want to either get a cheap car and get back onto an R1/R6 or just buy an R34 GTR and scrap the bike idea. Car is clean and reliable. No stains, burn marks, wear and tear in regards to the interior. Car body is clean, revs check is clear. I'm sure I left out some cosmetic modifications but people can see for themselves. Also comes with any original parts I can muster up but I do have all receipts and manuals for everything else. Pretty much my weekend car as I have a company van so it sits inside a garage for the week.

Modifications:

- Garrett 2860 -7 turbos

- Haltech Platinum Pro ECU (mafless tune)

- Nismo twin plate clutch

- 1000cc injectors

- Splitfire coil packs

- 115mm Greddy intercooler with piping kit

- Greddy air intake kit

- Tomei dump pipes

- Greddy front pipe

- Ballistic 5" body cat

- 3" Nismo cat back

- Bosche 044 fuel pump

- Bilstein suspension (shocks and springs)

- Rota 18" 9.5 +22 rims

- Kumho KU36 (265/35/18)

- DBA 4000 slotted/wiper front rotors

- Project MU race pads

- Hel braided brake lines

- Original front are rear strut bars

- Oil catch can

- Greddy oil filter relocation kit

- Nismo 320 km/h dash and triple center gauges

- HKS boost gauge mounted inside a Greddy A-pillar

- Blitz DSBC boost controller

- Nismo gear knob

- Short shifter

- Momo steering wheel with boss kit

- Blitz turbo timer

- Series 3 xenons

- Pioneer mp3/bluetooth/ipod ready head unit

- Fusion 10" sub/amp combo

- Tinted windows

5900142007_e5dc3d14bf_b.jpg

r33gtr310.jpg

5897444534_546e64911a_b.jpg

5904305199_8140ed10b4_b.jpg

_MG_7690.jpg

IMG_6757.jpg

5824101324_57f508b391_z.jpg

IMG_0023.jpg

IMG_0028.jpg

IMG_1520.jpg

IMG_1526.jpg

Link to comment
https://www.sau.com.au/forums/topic/370744-silver-r33-gtr-nsw/
Share on other sites

  • 2 weeks later...

Price drop:

$26,000

Don't be too alarmed though. My reasoning is because I got paid a very big pay check for all the overtime I've put in lately and rather than putting in more money into this car, I prefer to just lower the price of the car in regards to what I am willing to sell it at. I figure the longer I keep this car, I will eventually fall into temptation and spend big bucks on it.

Hi Mate,just wondering what area you are located in,cheers Matt

Campbelltown, NSW

VERY NICE RIDE MATE... HOPE IT SELLS.

Cheers, I half do and half don't hope that it sells haha

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...