Jump to content
SAU Community

Recommended Posts

Hi i bought an r33 as a doner car 4 the engine and box and now i have the shell need 2 get rid of it asap

The body was hit under the passanger door and there is dints on most panels but the car was drivable and registerd when i bought it i drove it home lol

it comes with all the panels {most arnt good]

interia is all there except the stereo surrond platic

5 stud hubs and brakes are in good condition

headlights

brake booster and master

diff and cradle [good no noises drove it 4 an hour]

rear lights

cluster is an auto 1

it was converted 2 a manual turbo at some stage so it has manual peddle box

Im keeping the stock alloys so u would need 2 bring 2 rims to roll it the rear has 1 space saver and 1 ford stockie

It doesnt come with engine box or loom or steering wheel or fuel pump

inspections r more than welcome just need it gone [ mums not happy its killing the grass hahaha]

Im located in melbourne west and my number is 0432165542

Looking 4 around 1500 open 2 offers need it gone would be good if someone wanted a drift pig

post-84764-0-04127900-1312065141_thumb.jpg

post-84764-0-08232400-1312065172_thumb.jpg

post-84764-0-35574300-1312065199_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/372553-r33-rolling-shell/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...