Jump to content
SAU Community

Painting Cam Covers With Caliper Paint

jjman

By jjman,
in Exterior & Interior Styling

 Share

Recommended Posts

jjman Mentor

jjman

Posted
Posted

Hey peeps. Taking off the cam coverages tomorrow to so the gasket seals n thought I might throw a layer of silver caliper paint on them. Has anybody tried this n will it stick properly?

Or is the surface texture and/or the current factory paint going to mess up the new paint?

Sorry if this has been covered before but I'm on my mobi n it can't so thread searches...

abd31 Apprentice

abd31

Posted
Posted

Hey peeps. Taking off the cam coverages tomorrow to so the gasket seals n thought I might throw a layer of silver caliper paint on them. Has anybody tried this n will it stick properly?

Or is the surface texture and/or the current factory paint going to mess up the new paint?

Sorry if this has been covered before but I'm on my mobi n it can't so thread searches...

My personal thoughts are that it is more than likely to work. But to be sure and get that better finish a little prep would probably go a long way. Some light sanding, primer etc....

abd31 Apprentice

abd31

Posted
Posted

Might pay to get a wire brush attachment that fits on a drill. Sand it back and give it a good clean, primer and paint. Be sure to get high temperature paint otherwise the whole thing will be an exercise in futility. Might also pay to get a heat gun from bunnings and go over it so the paint cures properly. I actually want to paint mine but CBF. seems too much work to get everything out and do the whole exercise. Maybe a project for summer.

good luck. Hope I helped

jjman Mentor

jjman

Posted
  • Author
Posted

actually i endned up bailing the respray job :happy:

after the time it took to get all of the intake shit off the motor to get at em properly and the exhaust shit too so i could clean up the oil weepage properly i was over it.

Also after a good degreasing and clean the covers actually came up pretty good so was content to put em back in...

I also didnt want to risk the job not turning out well n having anus looking covers in there. And i wouldnt have taken them back out after spending nigh on $200 for all of the seals, moons grommets...

no thanks, not going to f*k that job up and end up back at square 1.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Butters
      UniClutch

      By Butters · Posted

      Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...