Jump to content
SAU Community

Recommended Posts

Up For sale is my current daily driver. I am the second Australian owner. Previous owner imported it himself 11 years ago and owned it for 10. The car has been very reliable and was completely stock when i bought it. I've only done minor mods since. They include:

ENGINE

- 3 inch exhaust, gutted cat, no resonators, straight through rear muffler

- 3 inch dump and front pipe

- Blitz return flow fmic

- apexi intake pipe, drift pod

- turbotech boost controller @ 10 psi

- remapped ecu

- Greddy catch can

- 42mm alloy radiator

SUSPENSION AND BRAKES

- GTR shocks all round

- King springs on the front, whiteline springs rear (low but conservative)

- Bendix advanced pads all round

INTERIOR

- Momo steering wheel

- Speco gauges (boost, water temp, charge rate)

- replaced shifter and handbrake boots.

STEREO

- Alpine CDA-117e headunit (top of the range single din)

- Focal Polyglass Front splits

- Polk audio rear speakers

- Pioneer premier class d monoblock

- pioneer premier class d 4 channel

- 2x MTX thunder 8000 10"subs

- Dynamat applied to front doors, parcel shelf and boot lid.

- matching amps dont heat up and are mounted under front seats.

- Optima battery

SERVICING

- Oil change every 5000 inc oil filter

- gearbox oil replaced

- transfer and diff oils replaced

- brake and clutch fluid changed

- coolant flushed

- all power steering hoses replaced and fluid changed

- clutch master cylinder replaced

- rocker cover gaskets replaced

- Coil packs replaced with brand new genuine

- ignition harness replaced inc module

- g sensor replaced

- all tyres at 80%

- replaced noisy turbo

- window tint

For its age, the car runs very well. The body is relatively straight beside a few dents. The paint work is the only let down of the whole car. It would benefit from a full respray. Roadworthy will not be included but all standard parts will come with the car. the only other thing that needs to be done is the front driveshafts as the boots are split.

Asking for $6000 with stereo, or $5000 without which i think is pretty fair. Again, a roadworthy WILL NOT be supplied but it has reg till september this year.

For any other questions, contact me on 0433091345. The car is located in Northern suburbs melbourne.

Link to comment
https://www.sau.com.au/forums/topic/387095-fs-vic-93-r32-gts-4-manual-sedan/
Share on other sites

Hey man, Gonna be honest. Im looking at spending around 4500 on a car and i am interested in this

I dont want the Stereo. At the most just the head unit.

Where are you located in Melbourne and ill ask my big brother to bring me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...