Jump to content
SAU Community

Built Sr20Det Engine Package

25GTV
 Share

Recommended Posts

25GTV Experienced

25GTV

Posted
Posted

Hey guys, decided not to go ahead with the project and now must sell my engine package.

This motor was in my mates S13 until he crashed it 6 Months ago and I was going to put it in my Datsun.

Engine was only ever tuned up to 14psi as the original owner was a novice driver.

This motor is 100% and I have receipts to prove everything. I also have a short video of the engine running last week and pics of the comp test showing an even 151-154 across all 4 cylinders. Please send me your email for pics of the comp test and video.

Its been very reliable and will be good for many years to come.

S13 SR20DET

JE Pistons

Spool Rods

Crack Tested, Reground and Nitrite Crank

Race Series Rings and Bearings

Block has been bored and honed, acid dipped etc

Bottom end Balanced

Head has been acid dipped, bead blast, machined valves and seats, pressure tested and milled.

All seals and bearings where replaced during rebuild. Timing chain and tensioner were also replaced.

HKS GT28RS Turbo - Very good condition

Stainless Steel High Mount Manifold with 10mm flange.

JDM S15 480cc Injectors

Microtech LT10s and ignition computer with full loom.

Splitfire Coils

Fresh Excedy Sports Tuff Clutch Kit

S14 SR20DET Gearbox with CUSCO Shift

Tuned by CMR Performance

Even Comp Test - Performed on the 12th of January 2012

Engine was originally built 3 years ago but has only seen 8000kms.

Engine Produces 217 rwkw on only 14 psi but will do much more with retune and boost increase.

Price for everything - $5400 firm

Postage available at buyers expense...

Located in South Sydney - Near Sutherland.

I may part out the package only if someone buys the long motor first for $2900. (Long motor means no manifolds or accessories etc. Rocker cover down to the sump)

Serious buyers can call me on 0415334551 between 9:30 am and 9pm.

post-51468-0-17566200-1326800657_thumb.jpg

post-51468-0-90445100-1326800663_thumb.jpg

post-51468-0-82054700-1326800666_thumb.jpg

post-51468-0-72348800-1326800669_thumb.jpg

post-51468-0-40770200-1326800677_thumb.jpg

post-51468-0-60998000-1326800680_thumb.jpg

post-51468-0-11467900-1326800684_thumb.jpg

post-51468-0-65147400-1326800687_thumb.jpg

post-51468-0-17752200-1326800691_thumb.jpg

post-51468-0-25185300-1326800717_thumb.jpgpost-51468-0-77971000-1326800718_thumb.jpgpost-51468-0-74097800-1326800715_thumb.jpgpost-51468-0-90736500-1326800713_thumb.jpgpost-51468-0-70991200-1326800711_thumb.jpgpost-51468-0-91332600-1326800709_thumb.jpgpost-51468-0-69744100-1326800707_thumb.jpgpost-51468-0-84861600-1326800705_thumb.jpgpost-51468-0-80374900-1326800703_thumb.jpgpost-51468-0-87505200-1326800701_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/388577-built-sr20det-engine-package/
Share on other sites
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...