Jump to content
SAU Community

Recommended Posts

Hey I'm going through the process of replacing all my hoses, vaccine mainly, but I would like I do almost all of them,

Is their a whole kit u can get other from Nissan or aftermarket? Save some time and money, also to let me know what thee is to replace?

Link to comment
https://www.sau.com.au/forums/topic/391248-rb20-hose-replacement-kits/
Share on other sites

I talked to Nissan about this. They don't stock kits well the one i went to. they need to be ordered from Japan and are quite expensive. I think around couple hundy mark, that was just heater hoses aswell. A generic hose will prob cover some of the straighter ones, @ $5 a meter

I put a diagram up off all the hoses up with their part numbers and locations somewhere on here.

I'll have another search, didn't find much when I looked, yeah Nissan have been no real help, I was hoping for an aftermarket option, I did see import monster sell gtr kits once

R32 gtr hose kits are common and easily found, you can get them in blue silicone as well on ebay.

There probably are places that form the shaped hoses for you from silicone, that is an option you just need to have the hoses available to copy.

heres the hose diagrams for ya

http://www.skylinesaustralia.com/forums/topic/386846-rb20det-heater-hose-diagrams-with-nissan-part-numbers/page__p__6169818__hl__r32+hose+diagram__fromsearch__1#entry6169818

they are all moulded so you can't just buy a long peice of hose and think you're going to fit bits of that

nissan don't stock 'kits' you need to ring up or better yet go in and go through with them on the nissan FAST program which hoses you want

i did the hoses that run under and around the manifold on my r32 a while ago and they cost me like $300 wihtout doing the heater hoses

haven't tried the kits

yes the hoses are expensive, but it's something that you'll only do once in the time you own the car and it's awesome peice of mind once you do them knowing they aren't going to bust on you

I had a split heater hose under the manifold that needed fixing, Was a straight piece about 60mm long 1" wide and thats why I brought some hose from Repco to replace, rather than waiting 3 weeks 30 bucks later from Nissan.

Some are pretty straight forward and can be done using standard flexible hose.

Those diagrams are from Nissan, they are the codes that you need to give Nissan to get the right hoses from Japan. you cannot get a kit as such, but you can order all the hoses in the diagram & like Mystery-Kid said they are quite expensive.

Best thing to do is look at which hoses can be replaced with generic normal hose, and order the real awkward shaped hoses from Nissan eg: firewall entry hoses. There are a few that normal hose can replace, and will save you a lot of money, at around $30 a piece its something to consider.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...