Jump to content
SAU Community

Information On Trade-Ins

widebody180
 Share

Recommended Posts

widebody180 Collaborator

widebody180

Posted
Posted

It is time for me to get rid of my R32 GTR to make room for a more suitable family car. I have previously had my car on the market at what I thought was a reasonable price, with not even a bite. I've also been watching carsales and the trader forum here and there seems to be a fair few of these cars on the market, and not a lot of them actually being sold.

Do other people think that it is fair to say that the market is in a bit of oversupply at the moment?

I am really considering doing a trade in at a local dealer. I know that you never get the same value that you could in a private sale, but honestly it seems that I would have to drop the price down to not much more than trade in value to get a private sale anyway. The other important consideration is that I won't have to go through the effort of getting a roadworthy and possibly having to fix some issues. I don't think there is anything big that needs to be done, but the RWC guys always seem to find some problem, no matter what the condition of the car. I presently have my eye on a car at a dealer, the only issue is that the price of the car is about the same as the trade in value.

If I do a trade in for a car that is pretty much the same value, the dealer is obviously going to want to make some money, so what is the minimum difference that they will usually accept for a trade in?

Link to comment
https://www.sau.com.au/forums/topic/395411-information-on-trade-ins/
Share on other sites
Cowboy1600 Grand Master

Cowboy1600

Posted
Posted

The second hand market is dead, has been dead for years and will remain dead probably for ever.

What I would do is find out what you'll get for a trade in and then advertise it here for a grand or two above that. You'll likely move it very quickly (as it will no doubt be very cheap) and get a couple grand more than what a dealer is willing to give you.

ras1983 Experienced

ras1983

Posted
Posted

The second hand market is dead, has been dead for years and will remain dead probably for ever.

What I would do is find out what you'll get for a trade in and then advertise it here for a grand or two above that. You'll likely move it very quickly (as it will no doubt be very cheap) and get a couple grand more than what a dealer is willing to give you.

Second hand market has indeed been dead for several years, with the exception being R34 GTR, which still have some demand. The second hand market seems have completely stalled once the harsher p plate laws were introduced. Also, the fact that a lot of the cars are now 15-20 years old doesn't help. You can buy a hot hatch today that will keep up with the turbo monsters of yesteryear. Again, this hasn't helped the market.

The above is excellent advice. Get a trade in quote, advertise the car for a couple of grand more.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...