Jump to content
SAU Community

Recommended Posts

Hey Everyone!!

I have here for sale:

Genuine Volk Rays TE37SL Rims and KUMHO tyres

Description:

Up for sale is my beloved RARE brand new imported fro Japan

4X100 GENUINE FORGED MONOBLOCKVOLK RAYS TE37SL'z with KUMHO tyres

ALWAYS CLEANED AND BABIED EVERY 3 days,

the main face (Front) & inside the barrel always cleaned and waxed once every second week AND also tyre shined.

I'm a very fussy owner and i hate to look at them if their not clean and shiny :) haha!

i spend a good hour or two on them each time their cleaned,

SPECS:

-4X100

-17 X 7.5

- + 40

TYRES:

-KUMHO KU31

-205/40

-85% tread on the front

-90% tread on the rear

I have all of the original receipts and proof of purchase and authenticity from the moment they arrived in MELBOURNE and in the SHOP until NOW TODAY

I'm the ONE, ONLY & FIRST OWNER here in Melbourne & possibly the whole of Australia, to have this set of TE37SL's in 4X100 so very unique and RARE you won't see these anywhere else or anywhere near the quality, they are very light weight and their also good for daily wet and dry, BUT TRACK READY! ;)

210356_2012031359.jpg

210356_2012031343.jpg

210356_2012031322.jpg

211757_2012042357_tmb1.jpg

211757_2012042326_tmb1.jpg

Any questions, queries and offers at all please feel free to inbox or PM me :)

inspections are WELCOMED.

I LIVE IN THE WESTERN SUBURBS

the price is $3000 for the rims and tyres

ONO!!!!

if you can make me a reasonable offer their YOURS!!! without any furthur questions

THATS RIGHT YOU HEARD ME =)

THESE MUST GO AND MUST SELL!!!

MAKE ME A REASONABLE OFFER &

THEIR YOURS ^_^ WITHOUT FURTHER QUESTIONS

http://210356_2012031359.jpg[/img]

(low ballers will be ignored)

PM OR INBOX ME :)

THANKS GUYS <3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...