Jump to content
SAU Community

Wolf3D V4 Rb25Det Basemap

Karl Dawson

By Karl Dawson,
in Engines & Forced Induction

 Share

Recommended Posts

Karl Dawson Newbie

Karl Dawson

Posted
Posted

I recently purchased a Wolf3d V4 ecu to use on a rb30det I have just finished building. The ecu was used on a highly modified rb25det and is not suitable for my setup *obviously*, it floods the engine to the point it hydro/petrol locks it and will not start it.

Does anyone have a basemap for rb25det to suit? So the car can moved around/driven carefully to get dyno tuned?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/397718-wolf3d-v4-rb25det-basemap/
Share on other sites
GTRNUR Grand Master

GTRNUR

Posted
Posted

Are you saying that it litterally locks the engine by filling the cylinders? !!

That is not an ECU issue. More likely you have an injector stuck open, probably due to incorrect wiring.

The V400 running a 6 cylinder will have to run 2 injectors on each of the first 3 injector channels, so they run as either a batch or semi-sequential arrangement. No single map will be a plug and play solution for you.

Cam sensor configuration will dictate how it works too.

Upload a copy of your map I can check it out for you.

Karl Dawson Newbie

Karl Dawson

Posted
  • Author
Posted

Yes, full on locks the engine. Starts mint with rb25de ecu.

Yeah thats what I originally thought as well so replaced injectors, new seals and pintle caps, cleaned fuel rail etc. No change.

Would the lack of air temp sensor be the cause? using internal map sensor instead of AFM. Just remembered I don't have one currently connected at the moment since i'm waiting on IC piping to arrive.

Wolf3d map:

http://www.filefactory.com/file/76wx7opfc7o9/

GTRNUR Grand Master

GTRNUR

Posted
Posted

File factory isn't letting me download your map.

If your air temp compensation is turned off, the ecu won't apply any corrections. THis is pretty typical of a lot of wolf ecu's ive seen installed. Its worth sorting out though.

You should be using internal MAP, not the MAF sensor.

The hydraulicing issue is a serious one, and is probably something else. With the ignition off unplug all your injectors. Then turn the ignition to ON, and plug in one injector at a time. If you hear a click on any of the injectors as you plug them in, your wiring has issues. Injectors should remain closed unless the engine is running.

PM me a list of all your modifications, injector sizes and your email address. See if you can sort out that download link too.

  • 1 month later...
  • 5 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...