Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

Do you sell these with a fitting kit to suit a 1986 rx7 fc3s by any chance?

We don't stock specific kit's as yet but it does come with 2 strainers so that won't be a problem at all.

Whats the difference between 341 and 342?

Hey,

341 has an offset fitting 342 has an inline one. If not sure go with the 342 it's the most common one.

- Brendan

Do you know which kit would suit a S2 C34 stagea? The 341??

Hey,

In most cases the GSS432 is used (inline fitting) on all the Skylines (RB's) so I would say go with that one unless you require the offset fitting.

- Brendan

  • 5 months later...

Hi mate,

Wild stab in the dark but is this offer still available?

Oh yeah! Still in stock and ready to go.

Correct they are mufti-fit and come with 2x strainers to insure there is nothing they won't suit. :yes:

I got my package today thanks!

DSC_0139_zpsf5f2e407.jpg

When I got the box, it was loose. Is this everything I need? There were no instructions in the box?

That's it mate, 2 strainers terminals socket and fittings - it's all there.

These are universal kit's so installation instructions are not supplied, will depend on what you will be fitting it.

In most cases it's a straight fit with no fuss :thumbsup:

  • 2 weeks later...
  • 4 weeks later...
  • 1 year later...

At a fraction of the price of a new Nissan fuel pump, why not upgrade at the same time & save some big $$$





  • Similar Content

  • Latest Posts

    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
×
×
  • Create New...