Jump to content
SAU Community

Recommended Posts

i have a built rb26 still at the builders but is ment to be finished in a 2 weeks

i have lost intrest in this project and dont have the funds to finish it they way i wont it

and want to buy a house

specs intail

N1 block machend and decked and oil restrictor $3500

hks cams 264 and 272 10mm lift $1200

tomei oversize inlet valves $350

supertech oversize exh valves $250

tomei cam studs $300

ferrea duel valve springs with titanium retaines $1300

total seal rings gapless rings $600

tomei valve guides $700

hks valve stem seals $250

je 86.5mm pistons $900

arp head bolts $300

arp main studs $300

manley rods with arp studs$800

os giken cam gears $300

greddy clear timing cover $150

acl bearings $300

gates timing belt $120

nsk timing belt tensioner and idler $200

N1 water pump $250

tomei 1.5 head gasket exhaust and inlet gaskets $600

rear head dain and braided line $300

custom 8lt sump gated with extrnal pick up $1400

moroso extrnal oil pump $900

ross balance with tooth gear for pump and belt $100

standard oil pump with gears out new seals and gaskets $220

n1 crank balances and grub screwed $1000

ported and polished head and maching to fit cams $2500

sard 1000cc injectors $1000

greddy fuel rail $300

apexi power fc de-jetro and controller $1200

also have a trust td05 18g high mount twin turbos set up

with trust 50mm gate all braided lines, dump pipes and hot pipes

done little work since rebuild $4500

standard inlet manifold

welded dash 12 into rocker covers

not one expense spared other then inlet mainfod which was next on the list

built to run 30psi all day

that comes to $26050 plus anything i have forgotten which i think there will be

all work done lewis engines

not sure what to ask for this as it has cost a lot of money

$21000ono

located adel hills sa

Link to comment
https://www.sau.com.au/forums/topic/401161-built-rb26-n1-block-and-td05-turbos/
Share on other sites

This engine is built fine mate a lot of time and research have gone into this motor.

Also if u got nothing good to say dont post it. Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...