Jump to content
SAU Community

Recommended Posts

i have a built rb26 still at the builders but is ment to be finished in a 2 weeks

i have lost intrest in this project and dont have the funds to finish it they way i wont it

and want to buy a house

specs intail

N1 block machend and decked and oil restrictor $3500

hks cams 264 and 272 10mm lift $1200

tomei oversize inlet valves $350

supertech oversize exh valves $250

tomei cam studs $300

ferrea duel valve springs with titanium retaines $1300

total seal rings gapless rings $600

tomei valve guides $700

hks valve stem seals $250

je 86.5mm pistons $900

arp head bolts $300

arp main studs $300

manley rods with arp studs$800

os giken cam gears $300

greddy clear timing cover $150

acl bearings $300

gates timing belt $120

nsk timing belt tensioner and idler $200

N1 water pump $250

tomei 1.5 head gasket exhaust and inlet gaskets $600

rear head dain and braided line $300

custom 8lt sump gated with extrnal pick up $1400

moroso extrnal oil pump $900

ross balance with tooth gear for pump and belt $100

standard oil pump with gears out new seals and gaskets $220

n1 crank balances and grub screwed $1000

ported and polished head and maching to fit cams $2500

sard 1000cc injectors $1000

greddy fuel rail $300

apexi power fc de-jetro and controller $1200

also have a trust td05 18g high mount twin turbos set up

with trust 50mm gate all braided lines, dump pipes and hot pipes

done little work since rebuild $4500

standard inlet manifold

welded dash 12 into rocker covers

not one expense spared other then inlet mainfod which was next on the list

built to run 30psi all day

that comes to $26050 plus anything i have forgotten which i think there will be

all work done lewis engines

not sure what to ask for this as it has cost a lot of money

$21000ono

located adel hills sa

Link to comment
https://www.sau.com.au/forums/topic/401161-built-rb26-n1-block-and-td05-turbos/
Share on other sites

This engine is built fine mate a lot of time and research have gone into this motor.

Also if u got nothing good to say dont post it. Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm thinking that this is such a small part of the problem that you could easily forego the vac pump and just achieve 90% of what you need, which is keeping the gate open when off boost. It's not as if there are not already techniques to keep a gate fully closed under boost. After all, you have boost. Just use a wastegate actuator that will allow you to apply the boost on the appropriate side, just like every external gate out there.
    • Heres another fitment photo. redrilled the pattern to 5x112, and threw my audi´s rims on. had to touch the upper control arms with grinder, because the "sharp corner" was sticking about 2-3mm on the tire path. i have the "fender lip" mostly cut off, otherwise these (too) would contact with it. 20x9.5 ET25 rear    265/30 20x8.5 ET20 front    255/30 they are temporary, and look too big for the chassis. searching for 19s to it.
    • From experience, it will come back to bite you haha.
    • Background: my BMW 225i hatchback (rebodied MINI/X1) came with 3x RE003 and 1x Goodyear Asymmetric something. The RE003 roared and slid around, the Goodyear side was quiet and grippy. Definitely my car was thrashed before it got sent to dealers. My brother also got RE003 all round on his old VA WRX STI, I wasn't impressed with them, car was loud so can't comment on noise. Anyway, Hankook stopped making/updating V12 Evo2. So bought S1 Evo3 runflats. Great daily duties tyre and not that harsh ride. Tyre reviews site/youtube rated them as best stopping in the rain and I believe them. Next set, Goodyear Asymmetric 5 non-RFT. It beat PS4 in tests and is like $100 cheaper, so put them on. Great tyre, more grip then S1 Evo3 but a tad noisier as expected, still rocking them. Next set I am looking to go runflats, probably the new Hankook Evo. Although the new Pirelli PZ5 did well in tyrereviews test. Or go Goodyear Asymmetric 6 which was top tyre last year. The V12 Evo2 on my gen5 Liberty GT wagon did great in cold condition (drove to snowy mountains for a day so my husky can feel his ancestor's roots). Super impressive performance for $120 each lol. Never skimp on tyres, brakes, suspension. There's old pics of my R31's crappy random brake pads bending in the caliper at Oran Park track day somewhere around here. Anyway, my 2 cents.
×
×
  • Create New...