Jump to content
SAU Community

Bride Zeta Iii + Rail / Erg 4 Point Harness / A050 18 Inch / Shift Light / Ruzic Controller / Sparco Removable Steering Boss / R32 Gtr Front Seats


Recommended Posts

Quality parts out of a well looked after R32 GTR track car. Using winter to revise the setup of the car, hence the following is for sale:

1. $1000 - Genuine Bride Zeta III FIA Approved Race Bucket seat with low rails suit R32 GTR and I believe S series chassis as the rails have 2 mounting options at the rear. Excellent condition - no wear marks. Reason for sale - mounting new winged seat to roll cage.

post-3189-0-14588200-1340363471_thumb.jpgpost-3189-0-60141100-1340363510_thumb.jpgpost-3189-0-06522700-1340363526_thumb.jpg

2. $200 - ERG FIA Approved 4 Point Harness. Excellent condition. Reason for sale - bought a HANS specific harness to suit my HANS setup.

post-3189-0-91925200-1340363553_thumb.jpg

3. $150 - Ecliptech Shift Light Green/Amber/Red - excellent condition. Already configured to install directly into R32 GTSt/GTR just add velcro! I replaced this with a digital dash with integrated shift lights.

post-3189-0-00044200-1340363571_thumb.jpg

4. $1750 - Yokohama Advan A050 265/35/R18. Medium Compound, done one track day only. With wider rims now I run 295 width tyres.

5. $350 - Ruzic 4WD Controller. An excellent upgrade to increase the performance of the factory Attesa system. These controllers are very good - I am only selling due to a change in direction with the Attesa system which will be revealed soon on this forum.....(enough said :rolleyes: )

post-3189-0-33722300-1340363606_thumb.jpg

6. $500 - R32 GTR Factory front seats. With a clean, these will be scrub up well. Very minor cig burn on passenger seat, drivers seat very good condition given age.

post-3189-0-28179300-1340363626_thumb.jpg

7. $100 - Sparco style Removable steering wheel boss. I now have steering column mounted digital dash setup and I am changing the steering boss to weld on.

post-3189-0-87523800-1340363656_thumb.jpgpost-3189-0-56870400-1340363668_thumb.jpg

8. $30 - Superpro Diff nose bushes. These were removed after approx 100kms of use and replaced with solid alloy bushes. As new condition.

post-3189-0-84630700-1340363683_thumb.jpg

9. $60 - Subframe lock collars. Good condition. I went solid bushes for that exponential increase in NVH we all love!!

post-3189-0-73813500-1340363698_thumb.jpg

Also have factory computer for R32 GTR with removed speed cut and boost cut - make an offer.

Postage at buyers cost for the smaller items. Pickup or arrange courier etc yourself for the bigger items. All items in Adelaide Western Suburbs.

:action-smiley-069:

Edited by Blue32

7. $100 - Sparco style Removable steering wheel boss. I now have steering column mounted digital dash setup and I am changing the steering boss to weld on. SOLD PENDING PAYMENT thanks Spenda

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I'll get one of these also just for giggles
    • I bought 6 new spark plugs to compare readings. They will be here tomorrow and ill see if meter is far off if it all. I know one is at least reading 0 so its best replace all anyway if one is bad, from experience. I still have to test the harness just to be sure its not a double issue and I waste my time haha-the old plugs are iridium I always thought those lasted more than 50,000 km.
    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
×
×
  • Create New...