Jump to content
SAU Community

Recommended Posts

hey guys i have up for sale the following two sets of wheels.

Wheel no1

Weds Kranze Lxz chrome finish.

18x9+22 f

18x10+31 r

wheels comes with tires around 70% tread. wheels are in good condition. no buckle or chunks missing from wheels. wheels do have your usual gutter rash.

8ed1d3b0.jpg

e20a65d5.jpg

Price $2600 ono. happy to send interstate at YOUR cost

wheel no2:

SSR professor ms1. these are EOI atm as im not 100% sure if i want to fit them to my car or not.

wheels are finished in hyperblack chrome.

specs:

19" x 9 offset +11 step lip

19" x 10 offset +11 step lip

wheels are in good condition. cpiple of minor chips here and there. one wheel has a slight rash. nothing deep. will see upon inspection.

dont have any pics of the actual wheel yet. will post up soon.

$3000 ono

thanks

Ash

  • 2 weeks later...

Hey ash have a mate from JDMST thats keen on the MS1's are these the ones pictured here?

Where u located for trial fit?

http://www.skylinesaustralia.com/forums/topic/403213-nsw-fs-full-set-of-ssr-professor-ms1-hyperblack-chrome/

for sale: full set of SSR Professor MS1

specs:

19" x 9jj offset +11 NR with step lip

19" x 10jj offset +11 SL with step lip

hyper black colour with polished dish

sbc_lrg.jpg

condition of wheels is great with minor chip and mark here and there but nothing major.

there is one rash about 25cm from previous owner on one front wheel but is superficial and can be machined out easily (can arrange for this also), can arrange tyres also if need be.

RRP for these wheels are $900 per wheel before special coat and shipping

pics below are of the actual wheels on the car they were on (not a promo pic)

img8901z.jpg

img8920s.jpg

20120623143652.jpg

selling the set cheap for $2300 shipped anywhere in australia

pickup available also

please pm me

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...